--- Miniterm on /dev/ttyUSB0: 115200,8,N,1 ---
--- Quit: Ctrl+]  |  Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---

debug EMMC boot: print init OK
debug EMMC boot: send RST_N .
debug EMMC boot: start eMMC boot......
load fastboot1!

Switch to aarch64 mode. CPU0 executes at 0xf9801000!
NOTICE:  Booting Trusted Firmware
NOTICE:  BL1: v1.1(release):a0c0399
NOTICE:  BL1: Built : 13:23:48, May 22 2015
NOTICE:  succeed to init lpddr3 rank0 dram phy
INFO:    lpddr3_freq_init, set ddrc 533mhz
INFO:    init ddr3 rank0
INFO:    ddr3 rank1 init pass
INFO:    lpddr3_freq_init, set ddrc 800mhz
INFO:    init ddr3 rank0
INFO:    ddr3 rank1 init pass
INFO:    Elpida DDR
NOTICE:  BL1: Booting BL2
INFO:    [BDID] [fff91c18] midr: 0x410fd033
INFO:    [BDID] [fff91c1c] board type: 0
INFO:    [BDID] [fff91c20] board id: 0x2b
INFO:    init_acpu_dvfs: pmic version 17
INFO:    init_acpu_dvfs: ACPU_CHIP_MAX_FREQ=0x186a00.
INFO:    acpu_dvfs_volt_init: success!
INFO:    acpu_dvfs_set_freq: support freq num is 5
INFO:    acpu_dvfs_set_freq: start prof is 0x4
INFO:    acpu_dvfs_set_freq: magic is 0x5a5ac5c5
INFO:    acpu_dvfs_set_freq: voltage:
INFO:      - 0: 0x3a
INFO:      - 1: 0x3a
INFO:      - 2: 0x4a
INFO:      - 3: 0x5b
INFO:      - 4: 0x6b
NOTICE:  acpu_dvfs_set_freq: set acpu freq success!NOTICE:  BL2: v1.1(debug):a0c0399
NOTICE:  BL2: Built : 10:19:28, May 27 2015
INFO:    BL2: Loading BL3-0
INFO:    Using FIP
WARNING: Failed to access image 'bl30.bin' (-1)
ERROR:   Failed to load BL3-0 (-1)
ERROR:   Please burn mcu image:
ERROR:     sudo fastboot flash mcuimage mcuimage.bin
INFO:    BL2: TrustZone: protecting 16777216 bytes of memory at 0x3f000000
INFO:    BL2: Loading BL3-1
INFO:    Using FIP
INFO:    Loading file 'bl31.bin' at address 0xf9858000
INFO:    File 'bl31.bin' loaded: 0xf9858000 - 0xf9860010
INFO:    BL2: Loading BL3-2
INFO:    Using FIP
WARNING: Failed to access image 'bl32.bin' (-1)
WARNING: Failed to load BL3-2 (-1)
INFO:    BL2: Loading BL3-3
INFO:    Using FIP
INFO:    Loading file 'bl33.bin' at address 0x35000000
INFO:    File 'bl33.bin' loaded: 0x35000000 - 0x35042938
NOTICE:  BL1: Booting BL3-1
NOTICE:  BL3-1: v1.1(debug):a0c0399
NOTICE:  BL3-1: Built : 10:19:31, May 27 2015
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x35000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2015.04-00007-g1b3d379-dirty (May 27 2015 - 10:18:16) hikey_aemv8a

DRAM:  1008 MiB
MMC:   sd_card_detect: SD card present
HiKey DWMMC: 0, HiKey DWMMC: 1
In:    serial
Out:   serial
Err:   serial
Net:   Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot:  0 
Bad Linux ARM64 Image magic!
HiKey64#