Branch data Line data Source code
1 : : /*
2 : : * linux/include/linux/mmc/host.h
3 : : *
4 : : * This program is free software; you can redistribute it and/or modify
5 : : * it under the terms of the GNU General Public License version 2 as
6 : : * published by the Free Software Foundation.
7 : : *
8 : : * Host driver specific definitions.
9 : : */
10 : : #ifndef LINUX_MMC_HOST_H
11 : : #define LINUX_MMC_HOST_H
12 : :
13 : : #include <linux/leds.h>
14 : : #include <linux/mutex.h>
15 : : #include <linux/sched.h>
16 : : #include <linux/device.h>
17 : : #include <linux/fault-inject.h>
18 : : #include <linux/wakelock.h>
19 : :
20 : : #include <linux/mmc/core.h>
21 : : #include <linux/mmc/pm.h>
22 : :
23 : : struct mmc_ios {
24 : : unsigned int clock; /* clock rate */
25 : : unsigned short vdd;
26 : :
27 : : /* vdd stores the bit number of the selected voltage range from below. */
28 : :
29 : : unsigned char bus_mode; /* command output mode */
30 : :
31 : : #define MMC_BUSMODE_OPENDRAIN 1
32 : : #define MMC_BUSMODE_PUSHPULL 2
33 : :
34 : : unsigned char chip_select; /* SPI chip select */
35 : :
36 : : #define MMC_CS_DONTCARE 0
37 : : #define MMC_CS_HIGH 1
38 : : #define MMC_CS_LOW 2
39 : :
40 : : unsigned char power_mode; /* power supply mode */
41 : :
42 : : #define MMC_POWER_OFF 0
43 : : #define MMC_POWER_UP 1
44 : : #define MMC_POWER_ON 2
45 : :
46 : : unsigned char bus_width; /* data bus width */
47 : :
48 : : #define MMC_BUS_WIDTH_1 0
49 : : #define MMC_BUS_WIDTH_4 2
50 : : #define MMC_BUS_WIDTH_8 3
51 : :
52 : : unsigned char timing; /* timing specification used */
53 : :
54 : : #define MMC_TIMING_LEGACY 0
55 : : #define MMC_TIMING_MMC_HS 1
56 : : #define MMC_TIMING_SD_HS 2
57 : : #define MMC_TIMING_UHS_SDR12 3
58 : : #define MMC_TIMING_UHS_SDR25 4
59 : : #define MMC_TIMING_UHS_SDR50 5
60 : : #define MMC_TIMING_UHS_SDR104 6
61 : : #define MMC_TIMING_UHS_DDR50 7
62 : : #define MMC_TIMING_MMC_HS200 8
63 : :
64 : : #define MMC_SDR_MODE 0
65 : : #define MMC_1_2V_DDR_MODE 1
66 : : #define MMC_1_8V_DDR_MODE 2
67 : : #define MMC_1_2V_SDR_MODE 3
68 : : #define MMC_1_8V_SDR_MODE 4
69 : :
70 : : unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
71 : :
72 : : #define MMC_SIGNAL_VOLTAGE_330 0
73 : : #define MMC_SIGNAL_VOLTAGE_180 1
74 : : #define MMC_SIGNAL_VOLTAGE_120 2
75 : :
76 : : unsigned char drv_type; /* driver type (A, B, C, D) */
77 : :
78 : : #define MMC_SET_DRIVER_TYPE_B 0
79 : : #define MMC_SET_DRIVER_TYPE_A 1
80 : : #define MMC_SET_DRIVER_TYPE_C 2
81 : : #define MMC_SET_DRIVER_TYPE_D 3
82 : : };
83 : :
84 : : struct mmc_host_ops {
85 : : /*
86 : : * 'enable' is called when the host is claimed and 'disable' is called
87 : : * when the host is released. 'enable' and 'disable' are deprecated.
88 : : */
89 : : int (*enable)(struct mmc_host *host);
90 : : int (*disable)(struct mmc_host *host);
91 : : /*
92 : : * It is optional for the host to implement pre_req and post_req in
93 : : * order to support double buffering of requests (prepare one
94 : : * request while another request is active).
95 : : * pre_req() must always be followed by a post_req().
96 : : * To undo a call made to pre_req(), call post_req() with
97 : : * a nonzero err condition.
98 : : */
99 : : void (*post_req)(struct mmc_host *host, struct mmc_request *req,
100 : : int err);
101 : : void (*pre_req)(struct mmc_host *host, struct mmc_request *req,
102 : : bool is_first_req);
103 : : void (*request)(struct mmc_host *host, struct mmc_request *req);
104 : : /*
105 : : * Avoid calling these three functions too often or in a "fast path",
106 : : * since underlaying controller might implement them in an expensive
107 : : * and/or slow way.
108 : : *
109 : : * Also note that these functions might sleep, so don't call them
110 : : * in the atomic contexts!
111 : : *
112 : : * Return values for the get_ro callback should be:
113 : : * 0 for a read/write card
114 : : * 1 for a read-only card
115 : : * -ENOSYS when not supported (equal to NULL callback)
116 : : * or a negative errno value when something bad happened
117 : : *
118 : : * Return values for the get_cd callback should be:
119 : : * 0 for a absent card
120 : : * 1 for a present card
121 : : * -ENOSYS when not supported (equal to NULL callback)
122 : : * or a negative errno value when something bad happened
123 : : */
124 : : void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios);
125 : : int (*get_ro)(struct mmc_host *host);
126 : : int (*get_cd)(struct mmc_host *host);
127 : :
128 : : void (*enable_sdio_irq)(struct mmc_host *host, int enable);
129 : :
130 : : /* optional callback for HC quirks */
131 : : void (*init_card)(struct mmc_host *host, struct mmc_card *card);
132 : :
133 : : int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
134 : :
135 : : /* Check if the card is pulling dat[0:3] low */
136 : : int (*card_busy)(struct mmc_host *host);
137 : :
138 : : /* The tuning command opcode value is different for SD and eMMC cards */
139 : : int (*execute_tuning)(struct mmc_host *host, u32 opcode);
140 : : int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
141 : : void (*hw_reset)(struct mmc_host *host);
142 : : void (*card_event)(struct mmc_host *host);
143 : : };
144 : :
145 : : struct mmc_card;
146 : : struct device;
147 : :
148 : : struct mmc_async_req {
149 : : /* active mmc request */
150 : : struct mmc_request *mrq;
151 : : /*
152 : : * Check error status of completed mmc request.
153 : : * Returns 0 if success otherwise non zero.
154 : : */
155 : : int (*err_check) (struct mmc_card *, struct mmc_async_req *);
156 : : };
157 : :
158 : : /**
159 : : * struct mmc_slot - MMC slot functions
160 : : *
161 : : * @cd_irq: MMC/SD-card slot hotplug detection IRQ or -EINVAL
162 : : * @lock: protect the @handler_priv pointer
163 : : * @handler_priv: MMC/SD-card slot context
164 : : *
165 : : * Some MMC/SD host controllers implement slot-functions like card and
166 : : * write-protect detection natively. However, a large number of controllers
167 : : * leave these functions to the CPU. This struct provides a hook to attach
168 : : * such slot-function drivers.
169 : : */
170 : : struct mmc_slot {
171 : : int cd_irq;
172 : : struct mutex lock;
173 : : void *handler_priv;
174 : : };
175 : :
176 : : /**
177 : : * mmc_context_info - synchronization details for mmc context
178 : : * @is_done_rcv wake up reason was done request
179 : : * @is_new_req wake up reason was new request
180 : : * @is_waiting_last_req mmc context waiting for single running request
181 : : * @wait wait queue
182 : : * @lock lock to protect data fields
183 : : */
184 : : struct mmc_context_info {
185 : : bool is_done_rcv;
186 : : bool is_new_req;
187 : : bool is_waiting_last_req;
188 : : wait_queue_head_t wait;
189 : : spinlock_t lock;
190 : : };
191 : :
192 : : struct regulator;
193 : :
194 : : struct mmc_supply {
195 : : struct regulator *vmmc; /* Card power supply */
196 : : struct regulator *vqmmc; /* Optional Vccq supply */
197 : : };
198 : :
199 : : struct mmc_host {
200 : : struct device *parent;
201 : : struct device class_dev;
202 : : int index;
203 : : const struct mmc_host_ops *ops;
204 : : unsigned int f_min;
205 : : unsigned int f_max;
206 : : unsigned int f_init;
207 : : u32 ocr_avail;
208 : : u32 ocr_avail_sdio; /* SDIO-specific OCR */
209 : : u32 ocr_avail_sd; /* SD-specific OCR */
210 : : u32 ocr_avail_mmc; /* MMC-specific OCR */
211 : : struct notifier_block pm_notify;
212 : : u32 max_current_330;
213 : : u32 max_current_300;
214 : : u32 max_current_180;
215 : :
216 : : #define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */
217 : : #define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */
218 : : #define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */
219 : : #define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */
220 : : #define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */
221 : : #define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */
222 : : #define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */
223 : : #define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */
224 : : #define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */
225 : : #define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */
226 : : #define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */
227 : : #define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */
228 : : #define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */
229 : : #define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */
230 : : #define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */
231 : : #define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */
232 : : #define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */
233 : :
234 : : u32 caps; /* Host capabilities */
235 : :
236 : : #define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */
237 : : #define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */
238 : : #define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */
239 : : #define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */
240 : : #define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */
241 : : #define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */
242 : : #define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */
243 : : #define MMC_CAP_AGGRESSIVE_PM (1 << 7) /* Suspend (e)MMC/SD at idle */
244 : : #define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */
245 : : #define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */
246 : : #define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */
247 : : #define MMC_CAP_1_8V_DDR (1 << 11) /* can support */
248 : : /* DDR mode at 1.8V */
249 : : #define MMC_CAP_1_2V_DDR (1 << 12) /* can support */
250 : : /* DDR mode at 1.2V */
251 : : #define MMC_CAP_POWER_OFF_CARD (1 << 13) /* Can power off after boot */
252 : : #define MMC_CAP_BUS_WIDTH_TEST (1 << 14) /* CMD14/CMD19 bus width ok */
253 : : #define MMC_CAP_UHS_SDR12 (1 << 15) /* Host supports UHS SDR12 mode */
254 : : #define MMC_CAP_UHS_SDR25 (1 << 16) /* Host supports UHS SDR25 mode */
255 : : #define MMC_CAP_UHS_SDR50 (1 << 17) /* Host supports UHS SDR50 mode */
256 : : #define MMC_CAP_UHS_SDR104 (1 << 18) /* Host supports UHS SDR104 mode */
257 : : #define MMC_CAP_UHS_DDR50 (1 << 19) /* Host supports UHS DDR50 mode */
258 : : #define MMC_CAP_RUNTIME_RESUME (1 << 20) /* Resume at runtime_resume. */
259 : : #define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */
260 : : #define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */
261 : : #define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */
262 : : #define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */
263 : : #define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */
264 : :
265 : : u32 caps2; /* More host capabilities */
266 : :
267 : : #define MMC_CAP2_BOOTPART_NOACC (1 << 0) /* Boot partition no access */
268 : : #define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control */
269 : : #define MMC_CAP2_FULL_PWR_CYCLE (1 << 2) /* Can do full power cycle */
270 : : #define MMC_CAP2_NO_MULTI_READ (1 << 3) /* Multiblock reads don't work */
271 : : #define MMC_CAP2_NO_SLEEP_CMD (1 << 4) /* Don't allow sleep command */
272 : : #define MMC_CAP2_HS200_1_8V_SDR (1 << 5) /* can support */
273 : : #define MMC_CAP2_HS200_1_2V_SDR (1 << 6) /* can support */
274 : : #define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
275 : : MMC_CAP2_HS200_1_2V_SDR)
276 : : #define MMC_CAP2_BROKEN_VOLTAGE (1 << 7) /* Use the broken voltage */
277 : : #define MMC_CAP2_HC_ERASE_SZ (1 << 9) /* High-capacity erase size */
278 : : #define MMC_CAP2_CD_ACTIVE_HIGH (1 << 10) /* Card-detect signal active high */
279 : : #define MMC_CAP2_RO_ACTIVE_HIGH (1 << 11) /* Write-protect signal active high */
280 : : #define MMC_CAP2_PACKED_RD (1 << 12) /* Allow packed read */
281 : : #define MMC_CAP2_PACKED_WR (1 << 13) /* Allow packed write */
282 : : #define MMC_CAP2_PACKED_CMD (MMC_CAP2_PACKED_RD | \
283 : : MMC_CAP2_PACKED_WR)
284 : : #define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14) /* Don't power up before scan */
285 : : #define MMC_CAP2_SANITIZE (1 << 15) /* Support Sanitize */
286 : :
287 : : mmc_pm_flag_t pm_caps; /* supported pm features */
288 : :
289 : : #ifdef CONFIG_MMC_CLKGATE
290 : : int clk_requests; /* internal reference counter */
291 : : unsigned int clk_delay; /* number of MCI clk hold cycles */
292 : : bool clk_gated; /* clock gated */
293 : : struct delayed_work clk_gate_work; /* delayed clock gate */
294 : : unsigned int clk_old; /* old clock value cache */
295 : : spinlock_t clk_lock; /* lock for clk fields */
296 : : struct mutex clk_gate_mutex; /* mutex for clock gating */
297 : : struct device_attribute clkgate_delay_attr;
298 : : unsigned long clkgate_delay;
299 : : #endif
300 : :
301 : : /* host specific block data */
302 : : unsigned int max_seg_size; /* see blk_queue_max_segment_size */
303 : : unsigned short max_segs; /* see blk_queue_max_segments */
304 : : unsigned short unused;
305 : : unsigned int max_req_size; /* maximum number of bytes in one req */
306 : : unsigned int max_blk_size; /* maximum size of one mmc block */
307 : : unsigned int max_blk_count; /* maximum number of blocks in one req */
308 : : unsigned int max_discard_to; /* max. discard timeout in ms */
309 : :
310 : : /* private data */
311 : : spinlock_t lock; /* lock for claim and bus ops */
312 : :
313 : : struct mmc_ios ios; /* current io bus settings */
314 : :
315 : : /* group bitfields together to minimize padding */
316 : : unsigned int use_spi_crc:1;
317 : : unsigned int claimed:1; /* host exclusively claimed */
318 : : unsigned int bus_dead:1; /* bus has been released */
319 : : #ifdef CONFIG_MMC_DEBUG
320 : : unsigned int removed:1; /* host is being removed */
321 : : #endif
322 : :
323 : : int rescan_disable; /* disable card detection */
324 : : int rescan_entered; /* used with nonremovable devices */
325 : :
326 : : struct mmc_card *card; /* device attached to this host */
327 : :
328 : : wait_queue_head_t wq;
329 : : struct task_struct *claimer; /* task that has host claimed */
330 : : int claim_cnt; /* "claim" nesting count */
331 : :
332 : : struct delayed_work detect;
333 : : struct wake_lock detect_wake_lock;
334 : : int detect_change; /* card detect flag */
335 : : struct mmc_slot slot;
336 : :
337 : : const struct mmc_bus_ops *bus_ops; /* current bus driver */
338 : : unsigned int bus_refs; /* reference counter */
339 : :
340 : : unsigned int bus_resume_flags;
341 : : #define MMC_BUSRESUME_MANUAL_RESUME (1 << 0)
342 : : #define MMC_BUSRESUME_NEEDS_RESUME (1 << 1)
343 : :
344 : : unsigned int sdio_irqs;
345 : : struct task_struct *sdio_irq_thread;
346 : : bool sdio_irq_pending;
347 : : atomic_t sdio_irq_thread_abort;
348 : :
349 : : mmc_pm_flag_t pm_flags; /* requested pm features */
350 : :
351 : : struct led_trigger *led; /* activity led */
352 : :
353 : : #ifdef CONFIG_REGULATOR
354 : : bool regulator_enabled; /* regulator state */
355 : : #endif
356 : : struct mmc_supply supply;
357 : :
358 : : struct dentry *debugfs_root;
359 : :
360 : : struct mmc_async_req *areq; /* active async req */
361 : : struct mmc_context_info context_info; /* async synchronization info */
362 : :
363 : : #ifdef CONFIG_FAIL_MMC_REQUEST
364 : : struct fault_attr fail_mmc_request;
365 : : #endif
366 : :
367 : : unsigned int actual_clock; /* Actual HC clock rate */
368 : :
369 : : unsigned int slotno; /* used for sdio acpi binding */
370 : :
371 : : #ifdef CONFIG_MMC_EMBEDDED_SDIO
372 : : struct {
373 : : struct sdio_cis *cis;
374 : : struct sdio_cccr *cccr;
375 : : struct sdio_embedded_func *funcs;
376 : : int num_funcs;
377 : : } embedded_sdio_data;
378 : : #endif
379 : :
380 : : unsigned long private[0] ____cacheline_aligned;
381 : : };
382 : :
383 : : struct mmc_host *mmc_alloc_host(int extra, struct device *);
384 : : int mmc_add_host(struct mmc_host *);
385 : : void mmc_remove_host(struct mmc_host *);
386 : : void mmc_free_host(struct mmc_host *);
387 : : int mmc_of_parse(struct mmc_host *host);
388 : :
389 : : #ifdef CONFIG_MMC_EMBEDDED_SDIO
390 : : extern void mmc_set_embedded_sdio_data(struct mmc_host *host,
391 : : struct sdio_cis *cis,
392 : : struct sdio_cccr *cccr,
393 : : struct sdio_embedded_func *funcs,
394 : : int num_funcs);
395 : : #endif
396 : :
397 : : static inline void *mmc_priv(struct mmc_host *host)
398 : : {
399 : : return (void *)host->private;
400 : : }
401 : :
402 : : #define mmc_host_is_spi(host) ((host)->caps & MMC_CAP_SPI)
403 : :
404 : : #define mmc_dev(x) ((x)->parent)
405 : : #define mmc_classdev(x) (&(x)->class_dev)
406 : : #define mmc_hostname(x) (dev_name(&(x)->class_dev))
407 : : #define mmc_bus_needs_resume(host) ((host)->bus_resume_flags & MMC_BUSRESUME_NEEDS_RESUME)
408 : : #define mmc_bus_manual_resume(host) ((host)->bus_resume_flags & MMC_BUSRESUME_MANUAL_RESUME)
409 : :
410 : : static inline void mmc_set_bus_resume_policy(struct mmc_host *host, int manual)
411 : : {
412 : : if (manual)
413 : : host->bus_resume_flags |= MMC_BUSRESUME_MANUAL_RESUME;
414 : : else
415 : : host->bus_resume_flags &= ~MMC_BUSRESUME_MANUAL_RESUME;
416 : : }
417 : :
418 : : extern int mmc_resume_bus(struct mmc_host *host);
419 : :
420 : : int mmc_power_save_host(struct mmc_host *host);
421 : : int mmc_power_restore_host(struct mmc_host *host);
422 : :
423 : : void mmc_detect_change(struct mmc_host *, unsigned long delay);
424 : : void mmc_request_done(struct mmc_host *, struct mmc_request *);
425 : :
426 : : int mmc_cache_ctrl(struct mmc_host *, u8);
427 : :
428 : : static inline void mmc_signal_sdio_irq(struct mmc_host *host)
429 : : {
430 : 0 : host->ops->enable_sdio_irq(host, 0);
431 : 0 : host->sdio_irq_pending = true;
432 : 0 : wake_up_process(host->sdio_irq_thread);
433 : : }
434 : :
435 : : #ifdef CONFIG_REGULATOR
436 : : int mmc_regulator_get_ocrmask(struct regulator *supply);
437 : : int mmc_regulator_set_ocr(struct mmc_host *mmc,
438 : : struct regulator *supply,
439 : : unsigned short vdd_bit);
440 : : int mmc_regulator_get_supply(struct mmc_host *mmc);
441 : : #else
442 : : static inline int mmc_regulator_get_ocrmask(struct regulator *supply)
443 : : {
444 : : return 0;
445 : : }
446 : :
447 : : static inline int mmc_regulator_set_ocr(struct mmc_host *mmc,
448 : : struct regulator *supply,
449 : : unsigned short vdd_bit)
450 : : {
451 : : return 0;
452 : : }
453 : :
454 : : static inline int mmc_regulator_get_supply(struct mmc_host *mmc)
455 : : {
456 : : return 0;
457 : : }
458 : : #endif
459 : :
460 : : int mmc_pm_notify(struct notifier_block *notify_block, unsigned long, void *);
461 : :
462 : : /* Module parameter */
463 : : extern bool mmc_assume_removable;
464 : :
465 : : static inline int mmc_card_is_removable(struct mmc_host *host)
466 : : {
467 [ # # ][ # # ]: 0 : return !(host->caps & MMC_CAP_NONREMOVABLE) && mmc_assume_removable;
468 : : }
469 : :
470 : : static inline int mmc_card_keep_power(struct mmc_host *host)
471 : : {
472 : 0 : return host->pm_flags & MMC_PM_KEEP_POWER;
473 : : }
474 : :
475 : : static inline int mmc_card_wake_sdio_irq(struct mmc_host *host)
476 : : {
477 : 0 : return host->pm_flags & MMC_PM_WAKE_SDIO_IRQ;
478 : : }
479 : :
480 : : static inline int mmc_host_cmd23(struct mmc_host *host)
481 : : {
482 : 0 : return host->caps & MMC_CAP_CMD23;
483 : : }
484 : :
485 : : static inline int mmc_boot_partition_access(struct mmc_host *host)
486 : : {
487 : 0 : return !(host->caps2 & MMC_CAP2_BOOTPART_NOACC);
488 : : }
489 : :
490 : : static inline int mmc_host_uhs(struct mmc_host *host)
491 : : {
492 : 0 : return host->caps &
493 : : (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
494 : : MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |
495 : : MMC_CAP_UHS_DDR50);
496 : : }
497 : :
498 : : static inline int mmc_host_packed_wr(struct mmc_host *host)
499 : : {
500 : 0 : return host->caps2 & MMC_CAP2_PACKED_WR;
501 : : }
502 : :
503 : : #ifdef CONFIG_MMC_CLKGATE
504 : : void mmc_host_clk_hold(struct mmc_host *host);
505 : : void mmc_host_clk_release(struct mmc_host *host);
506 : : unsigned int mmc_host_clk_rate(struct mmc_host *host);
507 : :
508 : : #else
509 : : static inline void mmc_host_clk_hold(struct mmc_host *host)
510 : : {
511 : : }
512 : :
513 : : static inline void mmc_host_clk_release(struct mmc_host *host)
514 : : {
515 : : }
516 : :
517 : : static inline unsigned int mmc_host_clk_rate(struct mmc_host *host)
518 : : {
519 : : return host->ios.clock;
520 : : }
521 : : #endif
522 : : #endif /* LINUX_MMC_HOST_H */
|