Branch data Line data Source code
1 : : /*
2 : : * linux/drivers/mmc/core/mmc.c
3 : : *
4 : : * Copyright (C) 2003-2004 Russell King, All Rights Reserved.
5 : : * Copyright (C) 2005-2007 Pierre Ossman, All Rights Reserved.
6 : : * MMCv4 support Copyright (C) 2006 Philip Langdale, All Rights Reserved.
7 : : *
8 : : * This program is free software; you can redistribute it and/or modify
9 : : * it under the terms of the GNU General Public License version 2 as
10 : : * published by the Free Software Foundation.
11 : : */
12 : :
13 : : #include <linux/err.h>
14 : : #include <linux/slab.h>
15 : : #include <linux/stat.h>
16 : : #include <linux/pm_runtime.h>
17 : :
18 : : #include <linux/mmc/host.h>
19 : : #include <linux/mmc/card.h>
20 : : #include <linux/mmc/mmc.h>
21 : :
22 : : #include "core.h"
23 : : #include "bus.h"
24 : : #include "mmc_ops.h"
25 : : #include "sd_ops.h"
26 : :
27 : : static const unsigned int tran_exp[] = {
28 : : 10000, 100000, 1000000, 10000000,
29 : : 0, 0, 0, 0
30 : : };
31 : :
32 : : static const unsigned char tran_mant[] = {
33 : : 0, 10, 12, 13, 15, 20, 25, 30,
34 : : 35, 40, 45, 50, 55, 60, 70, 80,
35 : : };
36 : :
37 : : static const unsigned int tacc_exp[] = {
38 : : 1, 10, 100, 1000, 10000, 100000, 1000000, 10000000,
39 : : };
40 : :
41 : : static const unsigned int tacc_mant[] = {
42 : : 0, 10, 12, 13, 15, 20, 25, 30,
43 : : 35, 40, 45, 50, 55, 60, 70, 80,
44 : : };
45 : :
46 : : #define UNSTUFF_BITS(resp,start,size) \
47 : : ({ \
48 : : const int __size = size; \
49 : : const u32 __mask = (__size < 32 ? 1 << __size : 0) - 1; \
50 : : const int __off = 3 - ((start) / 32); \
51 : : const int __shft = (start) & 31; \
52 : : u32 __res; \
53 : : \
54 : : __res = resp[__off] >> __shft; \
55 : : if (__size + __shft > 32) \
56 : : __res |= resp[__off-1] << ((32 - __shft) % 32); \
57 : : __res & __mask; \
58 : : })
59 : :
60 : : /*
61 : : * Given the decoded CSD structure, decode the raw CID to our CID structure.
62 : : */
63 : 0 : static int mmc_decode_cid(struct mmc_card *card)
64 : : {
65 : : u32 *resp = card->raw_cid;
66 : :
67 : : /*
68 : : * The selection of the format here is based upon published
69 : : * specs from sandisk and from what people have reported.
70 : : */
71 [ # # # ]: 0 : switch (card->csd.mmca_vsn) {
72 : : case 0: /* MMC v1.0 - v1.2 */
73 : : case 1: /* MMC v1.4 */
74 : 0 : card->cid.manfid = UNSTUFF_BITS(resp, 104, 24);
75 : 0 : card->cid.prod_name[0] = UNSTUFF_BITS(resp, 96, 8);
76 : 0 : card->cid.prod_name[1] = UNSTUFF_BITS(resp, 88, 8);
77 : 0 : card->cid.prod_name[2] = UNSTUFF_BITS(resp, 80, 8);
78 : 0 : card->cid.prod_name[3] = UNSTUFF_BITS(resp, 72, 8);
79 : 0 : card->cid.prod_name[4] = UNSTUFF_BITS(resp, 64, 8);
80 : 0 : card->cid.prod_name[5] = UNSTUFF_BITS(resp, 56, 8);
81 : 0 : card->cid.prod_name[6] = UNSTUFF_BITS(resp, 48, 8);
82 : 0 : card->cid.hwrev = UNSTUFF_BITS(resp, 44, 4);
83 : 0 : card->cid.fwrev = UNSTUFF_BITS(resp, 40, 4);
84 : 0 : card->cid.serial = UNSTUFF_BITS(resp, 16, 24);
85 : 0 : card->cid.month = UNSTUFF_BITS(resp, 12, 4);
86 : 0 : card->cid.year = UNSTUFF_BITS(resp, 8, 4) + 1997;
87 : 0 : break;
88 : :
89 : : case 2: /* MMC v2.0 - v2.2 */
90 : : case 3: /* MMC v3.1 - v3.3 */
91 : : case 4: /* MMC v4 */
92 : 0 : card->cid.manfid = UNSTUFF_BITS(resp, 120, 8);
93 : 0 : card->cid.oemid = UNSTUFF_BITS(resp, 104, 16);
94 : 0 : card->cid.prod_name[0] = UNSTUFF_BITS(resp, 96, 8);
95 : 0 : card->cid.prod_name[1] = UNSTUFF_BITS(resp, 88, 8);
96 : 0 : card->cid.prod_name[2] = UNSTUFF_BITS(resp, 80, 8);
97 : 0 : card->cid.prod_name[3] = UNSTUFF_BITS(resp, 72, 8);
98 : 0 : card->cid.prod_name[4] = UNSTUFF_BITS(resp, 64, 8);
99 : 0 : card->cid.prod_name[5] = UNSTUFF_BITS(resp, 56, 8);
100 : 0 : card->cid.prv = UNSTUFF_BITS(resp, 48, 8);
101 : 0 : card->cid.serial = UNSTUFF_BITS(resp, 16, 32);
102 : 0 : card->cid.month = UNSTUFF_BITS(resp, 12, 4);
103 : 0 : card->cid.year = UNSTUFF_BITS(resp, 8, 4) + 1997;
104 : 0 : break;
105 : :
106 : : default:
107 : 0 : pr_err("%s: card has unknown MMCA version %d\n",
108 : : mmc_hostname(card->host), card->csd.mmca_vsn);
109 : 0 : return -EINVAL;
110 : : }
111 : :
112 : : return 0;
113 : : }
114 : :
115 : 0 : static void mmc_set_erase_size(struct mmc_card *card)
116 : : {
117 [ # # ]: 0 : if (card->ext_csd.erase_group_def & 1)
118 : 0 : card->erase_size = card->ext_csd.hc_erase_size;
119 : : else
120 : 0 : card->erase_size = card->csd.erase_size;
121 : :
122 : 0 : mmc_init_erase(card);
123 : 0 : }
124 : :
125 : : /*
126 : : * Given a 128-bit response, decode to our card CSD structure.
127 : : */
128 : 0 : static int mmc_decode_csd(struct mmc_card *card)
129 : : {
130 : : struct mmc_csd *csd = &card->csd;
131 : : unsigned int e, m, a, b;
132 : : u32 *resp = card->raw_csd;
133 : :
134 : : /*
135 : : * We only understand CSD structure v1.1 and v1.2.
136 : : * v1.2 has extra information in bits 15, 11 and 10.
137 : : * We also support eMMC v4.4 & v4.41.
138 : : */
139 : 0 : csd->structure = UNSTUFF_BITS(resp, 126, 2);
140 [ # # ]: 0 : if (csd->structure == 0) {
141 : 0 : pr_err("%s: unrecognised CSD structure version %d\n",
142 : : mmc_hostname(card->host), csd->structure);
143 : 0 : return -EINVAL;
144 : : }
145 : :
146 : 0 : csd->mmca_vsn = UNSTUFF_BITS(resp, 122, 4);
147 : 0 : m = UNSTUFF_BITS(resp, 115, 4);
148 : 0 : e = UNSTUFF_BITS(resp, 112, 3);
149 : 0 : csd->tacc_ns = (tacc_exp[e] * tacc_mant[m] + 9) / 10;
150 : 0 : csd->tacc_clks = UNSTUFF_BITS(resp, 104, 8) * 100;
151 : :
152 : 0 : m = UNSTUFF_BITS(resp, 99, 4);
153 : 0 : e = UNSTUFF_BITS(resp, 96, 3);
154 : 0 : csd->max_dtr = tran_exp[e] * tran_mant[m];
155 : 0 : csd->cmdclass = UNSTUFF_BITS(resp, 84, 12);
156 : :
157 : 0 : e = UNSTUFF_BITS(resp, 47, 3);
158 : 0 : m = UNSTUFF_BITS(resp, 62, 12);
159 : 0 : csd->capacity = (1 + m) << (e + 2);
160 : :
161 : 0 : csd->read_blkbits = UNSTUFF_BITS(resp, 80, 4);
162 : 0 : csd->read_partial = UNSTUFF_BITS(resp, 79, 1);
163 : 0 : csd->write_misalign = UNSTUFF_BITS(resp, 78, 1);
164 : 0 : csd->read_misalign = UNSTUFF_BITS(resp, 77, 1);
165 : 0 : csd->r2w_factor = UNSTUFF_BITS(resp, 26, 3);
166 : 0 : csd->write_blkbits = UNSTUFF_BITS(resp, 22, 4);
167 : 0 : csd->write_partial = UNSTUFF_BITS(resp, 21, 1);
168 : :
169 [ # # ]: 0 : if (csd->write_blkbits >= 9) {
170 : 0 : a = UNSTUFF_BITS(resp, 42, 5);
171 : 0 : b = UNSTUFF_BITS(resp, 37, 5);
172 : 0 : csd->erase_size = (a + 1) * (b + 1);
173 : 0 : csd->erase_size <<= csd->write_blkbits - 9;
174 : : }
175 : :
176 : : return 0;
177 : : }
178 : :
179 : : /*
180 : : * Read extended CSD.
181 : : */
182 : 0 : static int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd)
183 : : {
184 : : int err;
185 : : u8 *ext_csd;
186 : :
187 [ # # ]: 0 : BUG_ON(!card);
188 [ # # ]: 0 : BUG_ON(!new_ext_csd);
189 : :
190 : 0 : *new_ext_csd = NULL;
191 : :
192 [ # # ]: 0 : if (card->csd.mmca_vsn < CSD_SPEC_VER_4)
193 : : return 0;
194 : :
195 : : /*
196 : : * As the ext_csd is so large and mostly unused, we don't store the
197 : : * raw block in mmc_card.
198 : : */
199 : : ext_csd = kmalloc(512, GFP_KERNEL);
200 [ # # ]: 0 : if (!ext_csd) {
201 : 0 : pr_err("%s: could not allocate a buffer to "
202 : : "receive the ext_csd.\n", mmc_hostname(card->host));
203 : 0 : return -ENOMEM;
204 : : }
205 : :
206 : 0 : err = mmc_send_ext_csd(card, ext_csd);
207 [ # # ]: 0 : if (err) {
208 : 0 : kfree(ext_csd);
209 : 0 : *new_ext_csd = NULL;
210 : :
211 : : /* If the host or the card can't do the switch,
212 : : * fail more gracefully. */
213 [ # # ]: 0 : if ((err != -EINVAL)
214 : 0 : && (err != -ENOSYS)
215 [ # # ]: 0 : && (err != -EFAULT))
216 : : return err;
217 : :
218 : : /*
219 : : * High capacity cards should have this "magic" size
220 : : * stored in their CSD.
221 : : */
222 [ # # ]: 0 : if (card->csd.capacity == (4096 * 512)) {
223 : 0 : pr_err("%s: unable to read EXT_CSD "
224 : : "on a possible high capacity card. "
225 : : "Card will be ignored.\n",
226 : : mmc_hostname(card->host));
227 : : } else {
228 : 0 : pr_warning("%s: unable to read "
229 : : "EXT_CSD, performance might "
230 : : "suffer.\n",
231 : : mmc_hostname(card->host));
232 : : err = 0;
233 : : }
234 : : } else
235 : 0 : *new_ext_csd = ext_csd;
236 : :
237 : 0 : return err;
238 : : }
239 : :
240 : 0 : static void mmc_select_card_type(struct mmc_card *card)
241 : : {
242 : 0 : struct mmc_host *host = card->host;
243 : 0 : u8 card_type = card->ext_csd.raw_card_type & EXT_CSD_CARD_TYPE_MASK;
244 : 0 : u32 caps = host->caps, caps2 = host->caps2;
245 : : unsigned int hs_max_dtr = 0;
246 : :
247 [ # # ]: 0 : if (card_type & EXT_CSD_CARD_TYPE_26)
248 : : hs_max_dtr = MMC_HIGH_26_MAX_DTR;
249 : :
250 [ # # ][ # # ]: 0 : if (caps & MMC_CAP_MMC_HIGHSPEED &&
251 : 0 : card_type & EXT_CSD_CARD_TYPE_52)
252 : : hs_max_dtr = MMC_HIGH_52_MAX_DTR;
253 : :
254 [ # # ][ # # ]: 0 : if ((caps & MMC_CAP_1_8V_DDR &&
255 [ # # ]: 0 : card_type & EXT_CSD_CARD_TYPE_DDR_1_8V) ||
256 [ # # ]: 0 : (caps & MMC_CAP_1_2V_DDR &&
257 : 0 : card_type & EXT_CSD_CARD_TYPE_DDR_1_2V))
258 : : hs_max_dtr = MMC_HIGH_DDR_MAX_DTR;
259 : :
260 [ # # ][ # # ]: 0 : if ((caps2 & MMC_CAP2_HS200_1_8V_SDR &&
261 [ # # ]: 0 : card_type & EXT_CSD_CARD_TYPE_SDR_1_8V) ||
262 [ # # ]: 0 : (caps2 & MMC_CAP2_HS200_1_2V_SDR &&
263 : 0 : card_type & EXT_CSD_CARD_TYPE_SDR_1_2V))
264 : : hs_max_dtr = MMC_HS200_MAX_DTR;
265 : :
266 : 0 : card->ext_csd.hs_max_dtr = hs_max_dtr;
267 : 0 : card->ext_csd.card_type = card_type;
268 : 0 : }
269 : :
270 : : /*
271 : : * Decode extended CSD.
272 : : */
273 : 0 : static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
274 : : {
275 : : int err = 0, idx;
276 : : unsigned int part_size;
277 : : u8 hc_erase_grp_sz = 0, hc_wp_grp_sz = 0;
278 : :
279 [ # # ]: 0 : BUG_ON(!card);
280 : :
281 [ # # ]: 0 : if (!ext_csd)
282 : : return 0;
283 : :
284 : : /* Version is coded in the CSD_STRUCTURE byte in the EXT_CSD register */
285 : 0 : card->ext_csd.raw_ext_csd_structure = ext_csd[EXT_CSD_STRUCTURE];
286 [ # # ]: 0 : if (card->csd.structure == 3) {
287 [ # # ]: 0 : if (card->ext_csd.raw_ext_csd_structure > 2) {
288 : 0 : pr_err("%s: unrecognised EXT_CSD structure "
289 : : "version %d\n", mmc_hostname(card->host),
290 : : card->ext_csd.raw_ext_csd_structure);
291 : : err = -EINVAL;
292 : 0 : goto out;
293 : : }
294 : : }
295 : :
296 : 0 : card->ext_csd.rev = ext_csd[EXT_CSD_REV];
297 [ # # ]: 0 : if (card->ext_csd.rev > 7) {
298 : 0 : pr_err("%s: unrecognised EXT_CSD revision %d\n",
299 : : mmc_hostname(card->host), card->ext_csd.rev);
300 : : err = -EINVAL;
301 : 0 : goto out;
302 : : }
303 : :
304 : 0 : card->ext_csd.raw_sectors[0] = ext_csd[EXT_CSD_SEC_CNT + 0];
305 : 0 : card->ext_csd.raw_sectors[1] = ext_csd[EXT_CSD_SEC_CNT + 1];
306 : 0 : card->ext_csd.raw_sectors[2] = ext_csd[EXT_CSD_SEC_CNT + 2];
307 : 0 : card->ext_csd.raw_sectors[3] = ext_csd[EXT_CSD_SEC_CNT + 3];
308 [ # # ]: 0 : if (card->ext_csd.rev >= 2) {
309 : 0 : card->ext_csd.sectors =
310 : 0 : ext_csd[EXT_CSD_SEC_CNT + 0] << 0 |
311 : 0 : ext_csd[EXT_CSD_SEC_CNT + 1] << 8 |
312 : 0 : ext_csd[EXT_CSD_SEC_CNT + 2] << 16 |
313 : 0 : ext_csd[EXT_CSD_SEC_CNT + 3] << 24;
314 : :
315 : : /* Cards with density > 2GiB are sector addressed */
316 [ # # ]: 0 : if (card->ext_csd.sectors > (2u * 1024 * 1024 * 1024) / 512)
317 : 0 : mmc_card_set_blockaddr(card);
318 : : }
319 : :
320 : 0 : card->ext_csd.raw_card_type = ext_csd[EXT_CSD_CARD_TYPE];
321 : 0 : mmc_select_card_type(card);
322 : :
323 : 0 : card->ext_csd.raw_s_a_timeout = ext_csd[EXT_CSD_S_A_TIMEOUT];
324 : 0 : card->ext_csd.raw_erase_timeout_mult =
325 : : ext_csd[EXT_CSD_ERASE_TIMEOUT_MULT];
326 : 0 : card->ext_csd.raw_hc_erase_grp_size =
327 : : ext_csd[EXT_CSD_HC_ERASE_GRP_SIZE];
328 [ # # ]: 0 : if (card->ext_csd.rev >= 3) {
329 : 0 : u8 sa_shift = ext_csd[EXT_CSD_S_A_TIMEOUT];
330 : 0 : card->ext_csd.part_config = ext_csd[EXT_CSD_PART_CONFIG];
331 : :
332 : : /* EXT_CSD value is in units of 10ms, but we store in ms */
333 : 0 : card->ext_csd.part_time = 10 * ext_csd[EXT_CSD_PART_SWITCH_TIME];
334 : :
335 : : /* Sleep / awake timeout in 100ns units */
336 [ # # ]: 0 : if (sa_shift > 0 && sa_shift <= 0x17)
337 : 0 : card->ext_csd.sa_timeout =
338 : 0 : 1 << ext_csd[EXT_CSD_S_A_TIMEOUT];
339 : 0 : card->ext_csd.erase_group_def =
340 : : ext_csd[EXT_CSD_ERASE_GROUP_DEF];
341 : 0 : card->ext_csd.hc_erase_timeout = 300 *
342 : 0 : ext_csd[EXT_CSD_ERASE_TIMEOUT_MULT];
343 : 0 : card->ext_csd.hc_erase_size =
344 : 0 : ext_csd[EXT_CSD_HC_ERASE_GRP_SIZE] << 10;
345 : :
346 : 0 : card->ext_csd.rel_sectors = ext_csd[EXT_CSD_REL_WR_SEC_C];
347 : :
348 : : /*
349 : : * There are two boot regions of equal size, defined in
350 : : * multiples of 128K.
351 : : */
352 [ # # ][ # # ]: 0 : if (ext_csd[EXT_CSD_BOOT_MULT] && mmc_boot_partition_access(card->host)) {
353 [ # # ]: 0 : for (idx = 0; idx < MMC_NUM_BOOT_PARTITION; idx++) {
354 : 0 : part_size = ext_csd[EXT_CSD_BOOT_MULT] << 17;
355 : 0 : mmc_part_add(card, part_size,
356 : 0 : EXT_CSD_PART_CONFIG_ACC_BOOT0 + idx,
357 : : "boot%d", idx, true,
358 : : MMC_BLK_DATA_AREA_BOOT);
359 : : }
360 : : }
361 : : }
362 : :
363 : 0 : card->ext_csd.raw_hc_erase_gap_size =
364 : : ext_csd[EXT_CSD_HC_WP_GRP_SIZE];
365 : 0 : card->ext_csd.raw_sec_trim_mult =
366 : : ext_csd[EXT_CSD_SEC_TRIM_MULT];
367 : 0 : card->ext_csd.raw_sec_erase_mult =
368 : : ext_csd[EXT_CSD_SEC_ERASE_MULT];
369 : 0 : card->ext_csd.raw_sec_feature_support =
370 : : ext_csd[EXT_CSD_SEC_FEATURE_SUPPORT];
371 : 0 : card->ext_csd.raw_trim_mult =
372 : : ext_csd[EXT_CSD_TRIM_MULT];
373 : 0 : card->ext_csd.raw_partition_support = ext_csd[EXT_CSD_PARTITION_SUPPORT];
374 [ # # ]: 0 : if (card->ext_csd.rev >= 4) {
375 : : /*
376 : : * Enhanced area feature support -- check whether the eMMC
377 : : * card has the Enhanced area enabled. If so, export enhanced
378 : : * area offset and size to user by adding sysfs interface.
379 : : */
380 [ # # ][ # # ]: 0 : if ((ext_csd[EXT_CSD_PARTITION_SUPPORT] & 0x2) &&
381 : 0 : (ext_csd[EXT_CSD_PARTITION_ATTRIBUTE] & 0x1)) {
382 : 0 : hc_erase_grp_sz =
383 : : ext_csd[EXT_CSD_HC_ERASE_GRP_SIZE];
384 : 0 : hc_wp_grp_sz =
385 : : ext_csd[EXT_CSD_HC_WP_GRP_SIZE];
386 : :
387 : 0 : card->ext_csd.enhanced_area_en = 1;
388 : : /*
389 : : * calculate the enhanced data area offset, in bytes
390 : : */
391 : 0 : card->ext_csd.enhanced_area_offset =
392 : 0 : (ext_csd[139] << 24) + (ext_csd[138] << 16) +
393 : 0 : (ext_csd[137] << 8) + ext_csd[136];
394 [ # # ]: 0 : if (mmc_card_blockaddr(card))
395 : 0 : card->ext_csd.enhanced_area_offset <<= 9;
396 : : /*
397 : : * calculate the enhanced data area size, in kilobytes
398 : : */
399 : 0 : card->ext_csd.enhanced_area_size =
400 : 0 : (ext_csd[142] << 16) + (ext_csd[141] << 8) +
401 : 0 : ext_csd[140];
402 : 0 : card->ext_csd.enhanced_area_size *=
403 : 0 : (size_t)(hc_erase_grp_sz * hc_wp_grp_sz);
404 : 0 : card->ext_csd.enhanced_area_size <<= 9;
405 : : } else {
406 : : /*
407 : : * If the enhanced area is not enabled, disable these
408 : : * device attributes.
409 : : */
410 : 0 : card->ext_csd.enhanced_area_offset = -EINVAL;
411 : 0 : card->ext_csd.enhanced_area_size = -EINVAL;
412 : : }
413 : :
414 : : /*
415 : : * General purpose partition feature support --
416 : : * If ext_csd has the size of general purpose partitions,
417 : : * set size, part_cfg, partition name in mmc_part.
418 : : */
419 [ # # ]: 0 : if (ext_csd[EXT_CSD_PARTITION_SUPPORT] &
420 : : EXT_CSD_PART_SUPPORT_PART_EN) {
421 [ # # ]: 0 : if (card->ext_csd.enhanced_area_en != 1) {
422 : 0 : hc_erase_grp_sz =
423 : : ext_csd[EXT_CSD_HC_ERASE_GRP_SIZE];
424 : 0 : hc_wp_grp_sz =
425 : : ext_csd[EXT_CSD_HC_WP_GRP_SIZE];
426 : :
427 : 0 : card->ext_csd.enhanced_area_en = 1;
428 : : }
429 : :
430 [ # # ]: 0 : for (idx = 0; idx < MMC_NUM_GP_PARTITION; idx++) {
431 [ # # ][ # # ]: 0 : if (!ext_csd[EXT_CSD_GP_SIZE_MULT + idx * 3] &&
432 [ # # ]: 0 : !ext_csd[EXT_CSD_GP_SIZE_MULT + idx * 3 + 1] &&
433 : 0 : !ext_csd[EXT_CSD_GP_SIZE_MULT + idx * 3 + 2])
434 : 0 : continue;
435 : 0 : part_size =
436 : 0 : (ext_csd[EXT_CSD_GP_SIZE_MULT + idx * 3 + 2]
437 : 0 : << 16) +
438 : 0 : (ext_csd[EXT_CSD_GP_SIZE_MULT + idx * 3 + 1]
439 : 0 : << 8) +
440 : : ext_csd[EXT_CSD_GP_SIZE_MULT + idx * 3];
441 : 0 : part_size *= (size_t)(hc_erase_grp_sz *
442 : : hc_wp_grp_sz);
443 : 0 : mmc_part_add(card, part_size << 19,
444 : 0 : EXT_CSD_PART_CONFIG_ACC_GP0 + idx,
445 : : "gp%d", idx, false,
446 : : MMC_BLK_DATA_AREA_GP);
447 : : }
448 : : }
449 : 0 : card->ext_csd.sec_trim_mult =
450 : 0 : ext_csd[EXT_CSD_SEC_TRIM_MULT];
451 : 0 : card->ext_csd.sec_erase_mult =
452 : 0 : ext_csd[EXT_CSD_SEC_ERASE_MULT];
453 : 0 : card->ext_csd.sec_feature_support =
454 : : ext_csd[EXT_CSD_SEC_FEATURE_SUPPORT];
455 : 0 : card->ext_csd.trim_timeout = 300 *
456 : 0 : ext_csd[EXT_CSD_TRIM_MULT];
457 : :
458 : : /*
459 : : * Note that the call to mmc_part_add above defaults to read
460 : : * only. If this default assumption is changed, the call must
461 : : * take into account the value of boot_locked below.
462 : : */
463 : 0 : card->ext_csd.boot_ro_lock = ext_csd[EXT_CSD_BOOT_WP];
464 : 0 : card->ext_csd.boot_ro_lockable = true;
465 : :
466 : : /* Save power class values */
467 : 0 : card->ext_csd.raw_pwr_cl_52_195 =
468 : : ext_csd[EXT_CSD_PWR_CL_52_195];
469 : 0 : card->ext_csd.raw_pwr_cl_26_195 =
470 : : ext_csd[EXT_CSD_PWR_CL_26_195];
471 : 0 : card->ext_csd.raw_pwr_cl_52_360 =
472 : : ext_csd[EXT_CSD_PWR_CL_52_360];
473 : 0 : card->ext_csd.raw_pwr_cl_26_360 =
474 : : ext_csd[EXT_CSD_PWR_CL_26_360];
475 : 0 : card->ext_csd.raw_pwr_cl_200_195 =
476 : : ext_csd[EXT_CSD_PWR_CL_200_195];
477 : 0 : card->ext_csd.raw_pwr_cl_200_360 =
478 : : ext_csd[EXT_CSD_PWR_CL_200_360];
479 : 0 : card->ext_csd.raw_pwr_cl_ddr_52_195 =
480 : : ext_csd[EXT_CSD_PWR_CL_DDR_52_195];
481 : 0 : card->ext_csd.raw_pwr_cl_ddr_52_360 =
482 : : ext_csd[EXT_CSD_PWR_CL_DDR_52_360];
483 : : }
484 : :
485 [ # # ]: 0 : if (card->ext_csd.rev >= 5) {
486 : : /* Adjust production date as per JEDEC JESD84-B451 */
487 [ # # ]: 0 : if (card->cid.year < 2010)
488 : 0 : card->cid.year += 16;
489 : :
490 : : /* check whether the eMMC card supports BKOPS */
491 [ # # ]: 0 : if (ext_csd[EXT_CSD_BKOPS_SUPPORT] & 0x1) {
492 : 0 : card->ext_csd.bkops = 1;
493 : 0 : card->ext_csd.bkops_en = ext_csd[EXT_CSD_BKOPS_EN];
494 : 0 : card->ext_csd.raw_bkops_status =
495 : : ext_csd[EXT_CSD_BKOPS_STATUS];
496 [ # # ]: 0 : if (!card->ext_csd.bkops_en)
497 : 0 : pr_info("%s: BKOPS_EN bit is not set\n",
498 : : mmc_hostname(card->host));
499 : : }
500 : :
501 : : /* check whether the eMMC card supports HPI */
502 [ # # ]: 0 : if (ext_csd[EXT_CSD_HPI_FEATURES] & 0x1) {
503 : 0 : card->ext_csd.hpi = 1;
504 [ # # ]: 0 : if (ext_csd[EXT_CSD_HPI_FEATURES] & 0x2)
505 : 0 : card->ext_csd.hpi_cmd = MMC_STOP_TRANSMISSION;
506 : : else
507 : 0 : card->ext_csd.hpi_cmd = MMC_SEND_STATUS;
508 : : /*
509 : : * Indicate the maximum timeout to close
510 : : * a command interrupted by HPI
511 : : */
512 : 0 : card->ext_csd.out_of_int_time =
513 : 0 : ext_csd[EXT_CSD_OUT_OF_INTERRUPT_TIME] * 10;
514 : : }
515 : :
516 : 0 : card->ext_csd.rel_param = ext_csd[EXT_CSD_WR_REL_PARAM];
517 : 0 : card->ext_csd.rst_n_function = ext_csd[EXT_CSD_RST_N_FUNCTION];
518 : :
519 : : /*
520 : : * RPMB regions are defined in multiples of 128K.
521 : : */
522 : 0 : card->ext_csd.raw_rpmb_size_mult = ext_csd[EXT_CSD_RPMB_MULT];
523 [ # # ][ # # ]: 0 : if (ext_csd[EXT_CSD_RPMB_MULT] && mmc_host_cmd23(card->host)) {
524 : 0 : mmc_part_add(card, ext_csd[EXT_CSD_RPMB_MULT] << 17,
525 : : EXT_CSD_PART_CONFIG_ACC_RPMB,
526 : : "rpmb", 0, false,
527 : : MMC_BLK_DATA_AREA_RPMB);
528 : : }
529 : : }
530 : :
531 : 0 : card->ext_csd.raw_erased_mem_count = ext_csd[EXT_CSD_ERASED_MEM_CONT];
532 [ # # ]: 0 : if (ext_csd[EXT_CSD_ERASED_MEM_CONT])
533 : 0 : card->erased_byte = 0xFF;
534 : : else
535 : 0 : card->erased_byte = 0x0;
536 : :
537 : : /* eMMC v4.5 or later */
538 [ # # ]: 0 : if (card->ext_csd.rev >= 6) {
539 : 0 : card->ext_csd.feature_support |= MMC_DISCARD_FEATURE;
540 : :
541 : 0 : card->ext_csd.generic_cmd6_time = 10 *
542 : 0 : ext_csd[EXT_CSD_GENERIC_CMD6_TIME];
543 : 0 : card->ext_csd.power_off_longtime = 10 *
544 : 0 : ext_csd[EXT_CSD_POWER_OFF_LONG_TIME];
545 : :
546 : 0 : card->ext_csd.cache_size =
547 : 0 : ext_csd[EXT_CSD_CACHE_SIZE + 0] << 0 |
548 : 0 : ext_csd[EXT_CSD_CACHE_SIZE + 1] << 8 |
549 : 0 : ext_csd[EXT_CSD_CACHE_SIZE + 2] << 16 |
550 : 0 : ext_csd[EXT_CSD_CACHE_SIZE + 3] << 24;
551 : :
552 [ # # ]: 0 : if (ext_csd[EXT_CSD_DATA_SECTOR_SIZE] == 1)
553 : 0 : card->ext_csd.data_sector_size = 4096;
554 : : else
555 : 0 : card->ext_csd.data_sector_size = 512;
556 : :
557 [ # # ][ # # ]: 0 : if ((ext_csd[EXT_CSD_DATA_TAG_SUPPORT] & 1) &&
558 : 0 : (ext_csd[EXT_CSD_TAG_UNIT_SIZE] <= 8)) {
559 : 0 : card->ext_csd.data_tag_unit_size =
560 : 0 : ((unsigned int) 1 << ext_csd[EXT_CSD_TAG_UNIT_SIZE]) *
561 : 0 : (card->ext_csd.data_sector_size);
562 : : } else {
563 : 0 : card->ext_csd.data_tag_unit_size = 0;
564 : : }
565 : :
566 : 0 : card->ext_csd.max_packed_writes =
567 : : ext_csd[EXT_CSD_MAX_PACKED_WRITES];
568 : 0 : card->ext_csd.max_packed_reads =
569 : : ext_csd[EXT_CSD_MAX_PACKED_READS];
570 : : } else {
571 : 0 : card->ext_csd.data_sector_size = 512;
572 : : }
573 : :
574 : : out:
575 : 0 : return err;
576 : : }
577 : :
578 : : static inline void mmc_free_ext_csd(u8 *ext_csd)
579 : : {
580 : 0 : kfree(ext_csd);
581 : : }
582 : :
583 : :
584 : 0 : static int mmc_compare_ext_csds(struct mmc_card *card, unsigned bus_width)
585 : : {
586 : : u8 *bw_ext_csd;
587 : : int err;
588 : :
589 [ # # ]: 0 : if (bus_width == MMC_BUS_WIDTH_1)
590 : : return 0;
591 : :
592 : 0 : err = mmc_get_ext_csd(card, &bw_ext_csd);
593 : :
594 [ # # ][ # # ]: 0 : if (err || bw_ext_csd == NULL) {
595 : : err = -EINVAL;
596 : : goto out;
597 : : }
598 : :
599 : : /* only compare read only fields */
600 [ # # ][ # # ]: 0 : err = !((card->ext_csd.raw_partition_support ==
601 [ # # ]: 0 : bw_ext_csd[EXT_CSD_PARTITION_SUPPORT]) &&
602 : 0 : (card->ext_csd.raw_erased_mem_count ==
603 [ # # ]: 0 : bw_ext_csd[EXT_CSD_ERASED_MEM_CONT]) &&
604 : 0 : (card->ext_csd.rev ==
605 [ # # ]: 0 : bw_ext_csd[EXT_CSD_REV]) &&
606 : 0 : (card->ext_csd.raw_ext_csd_structure ==
607 [ # # ]: 0 : bw_ext_csd[EXT_CSD_STRUCTURE]) &&
608 : 0 : (card->ext_csd.raw_card_type ==
609 [ # # ]: 0 : bw_ext_csd[EXT_CSD_CARD_TYPE]) &&
610 : 0 : (card->ext_csd.raw_s_a_timeout ==
611 [ # # ]: 0 : bw_ext_csd[EXT_CSD_S_A_TIMEOUT]) &&
612 : 0 : (card->ext_csd.raw_hc_erase_gap_size ==
613 [ # # ]: 0 : bw_ext_csd[EXT_CSD_HC_WP_GRP_SIZE]) &&
614 : 0 : (card->ext_csd.raw_erase_timeout_mult ==
615 [ # # ]: 0 : bw_ext_csd[EXT_CSD_ERASE_TIMEOUT_MULT]) &&
616 : 0 : (card->ext_csd.raw_hc_erase_grp_size ==
617 [ # # ]: 0 : bw_ext_csd[EXT_CSD_HC_ERASE_GRP_SIZE]) &&
618 : 0 : (card->ext_csd.raw_sec_trim_mult ==
619 [ # # ]: 0 : bw_ext_csd[EXT_CSD_SEC_TRIM_MULT]) &&
620 : 0 : (card->ext_csd.raw_sec_erase_mult ==
621 [ # # ]: 0 : bw_ext_csd[EXT_CSD_SEC_ERASE_MULT]) &&
622 : 0 : (card->ext_csd.raw_sec_feature_support ==
623 [ # # ]: 0 : bw_ext_csd[EXT_CSD_SEC_FEATURE_SUPPORT]) &&
624 : 0 : (card->ext_csd.raw_trim_mult ==
625 [ # # ]: 0 : bw_ext_csd[EXT_CSD_TRIM_MULT]) &&
626 : 0 : (card->ext_csd.raw_sectors[0] ==
627 [ # # ]: 0 : bw_ext_csd[EXT_CSD_SEC_CNT + 0]) &&
628 : 0 : (card->ext_csd.raw_sectors[1] ==
629 [ # # ]: 0 : bw_ext_csd[EXT_CSD_SEC_CNT + 1]) &&
630 : 0 : (card->ext_csd.raw_sectors[2] ==
631 [ # # ]: 0 : bw_ext_csd[EXT_CSD_SEC_CNT + 2]) &&
632 : 0 : (card->ext_csd.raw_sectors[3] ==
633 [ # # ]: 0 : bw_ext_csd[EXT_CSD_SEC_CNT + 3]) &&
634 : 0 : (card->ext_csd.raw_pwr_cl_52_195 ==
635 [ # # ]: 0 : bw_ext_csd[EXT_CSD_PWR_CL_52_195]) &&
636 : 0 : (card->ext_csd.raw_pwr_cl_26_195 ==
637 [ # # ]: 0 : bw_ext_csd[EXT_CSD_PWR_CL_26_195]) &&
638 : 0 : (card->ext_csd.raw_pwr_cl_52_360 ==
639 [ # # ]: 0 : bw_ext_csd[EXT_CSD_PWR_CL_52_360]) &&
640 : 0 : (card->ext_csd.raw_pwr_cl_26_360 ==
641 [ # # ]: 0 : bw_ext_csd[EXT_CSD_PWR_CL_26_360]) &&
642 : 0 : (card->ext_csd.raw_pwr_cl_200_195 ==
643 [ # # ]: 0 : bw_ext_csd[EXT_CSD_PWR_CL_200_195]) &&
644 : 0 : (card->ext_csd.raw_pwr_cl_200_360 ==
645 [ # # ]: 0 : bw_ext_csd[EXT_CSD_PWR_CL_200_360]) &&
646 : 0 : (card->ext_csd.raw_pwr_cl_ddr_52_195 ==
647 : 0 : bw_ext_csd[EXT_CSD_PWR_CL_DDR_52_195]) &&
648 : 0 : (card->ext_csd.raw_pwr_cl_ddr_52_360 ==
649 : 0 : bw_ext_csd[EXT_CSD_PWR_CL_DDR_52_360]));
650 [ # # ]: 0 : if (err)
651 : : err = -EINVAL;
652 : :
653 : : out:
654 : 0 : mmc_free_ext_csd(bw_ext_csd);
655 : 0 : return err;
656 : : }
657 : :
658 : 0 : MMC_DEV_ATTR(cid, "%08x%08x%08x%08x\n", card->raw_cid[0], card->raw_cid[1],
659 : : card->raw_cid[2], card->raw_cid[3]);
660 : 0 : MMC_DEV_ATTR(csd, "%08x%08x%08x%08x\n", card->raw_csd[0], card->raw_csd[1],
661 : : card->raw_csd[2], card->raw_csd[3]);
662 : 0 : MMC_DEV_ATTR(date, "%02d/%04d\n", card->cid.month, card->cid.year);
663 : 0 : MMC_DEV_ATTR(erase_size, "%u\n", card->erase_size << 9);
664 : 0 : MMC_DEV_ATTR(preferred_erase_size, "%u\n", card->pref_erase << 9);
665 : 0 : MMC_DEV_ATTR(fwrev, "0x%x\n", card->cid.fwrev);
666 : 0 : MMC_DEV_ATTR(hwrev, "0x%x\n", card->cid.hwrev);
667 : 0 : MMC_DEV_ATTR(manfid, "0x%06x\n", card->cid.manfid);
668 : 0 : MMC_DEV_ATTR(name, "%s\n", card->cid.prod_name);
669 : 0 : MMC_DEV_ATTR(oemid, "0x%04x\n", card->cid.oemid);
670 : 0 : MMC_DEV_ATTR(prv, "0x%x\n", card->cid.prv);
671 : 0 : MMC_DEV_ATTR(serial, "0x%08x\n", card->cid.serial);
672 : 0 : MMC_DEV_ATTR(enhanced_area_offset, "%llu\n",
673 : : card->ext_csd.enhanced_area_offset);
674 : 0 : MMC_DEV_ATTR(enhanced_area_size, "%u\n", card->ext_csd.enhanced_area_size);
675 : 0 : MMC_DEV_ATTR(raw_rpmb_size_mult, "%#x\n", card->ext_csd.raw_rpmb_size_mult);
676 : 0 : MMC_DEV_ATTR(rel_sectors, "%#x\n", card->ext_csd.rel_sectors);
677 : :
678 : : static struct attribute *mmc_std_attrs[] = {
679 : : &dev_attr_cid.attr,
680 : : &dev_attr_csd.attr,
681 : : &dev_attr_date.attr,
682 : : &dev_attr_erase_size.attr,
683 : : &dev_attr_preferred_erase_size.attr,
684 : : &dev_attr_fwrev.attr,
685 : : &dev_attr_hwrev.attr,
686 : : &dev_attr_manfid.attr,
687 : : &dev_attr_name.attr,
688 : : &dev_attr_oemid.attr,
689 : : &dev_attr_prv.attr,
690 : : &dev_attr_serial.attr,
691 : : &dev_attr_enhanced_area_offset.attr,
692 : : &dev_attr_enhanced_area_size.attr,
693 : : &dev_attr_raw_rpmb_size_mult.attr,
694 : : &dev_attr_rel_sectors.attr,
695 : : NULL,
696 : : };
697 : :
698 : : static struct attribute_group mmc_std_attr_group = {
699 : : .attrs = mmc_std_attrs,
700 : : };
701 : :
702 : : static const struct attribute_group *mmc_attr_groups[] = {
703 : : &mmc_std_attr_group,
704 : : NULL,
705 : : };
706 : :
707 : : static struct device_type mmc_type = {
708 : : .groups = mmc_attr_groups,
709 : : };
710 : :
711 : : /*
712 : : * Select the PowerClass for the current bus width
713 : : * If power class is defined for 4/8 bit bus in the
714 : : * extended CSD register, select it by executing the
715 : : * mmc_switch command.
716 : : */
717 : 0 : static int mmc_select_powerclass(struct mmc_card *card,
718 : : unsigned int bus_width)
719 : : {
720 : : int err = 0;
721 : : unsigned int pwrclass_val = 0;
722 : : struct mmc_host *host;
723 : :
724 [ # # ]: 0 : BUG_ON(!card);
725 : :
726 : 0 : host = card->host;
727 [ # # ]: 0 : BUG_ON(!host);
728 : :
729 : : /* Power class selection is supported for versions >= 4.0 */
730 [ # # ]: 0 : if (card->csd.mmca_vsn < CSD_SPEC_VER_4)
731 : : return 0;
732 : :
733 : : /* Power class values are defined only for 4/8 bit bus */
734 [ # # ]: 0 : if (bus_width == EXT_CSD_BUS_WIDTH_1)
735 : : return 0;
736 : :
737 [ # # # ]: 0 : switch (1 << host->ios.vdd) {
738 : : case MMC_VDD_165_195:
739 [ # # ]: 0 : if (host->ios.clock <= 26000000)
740 : 0 : pwrclass_val = card->ext_csd.raw_pwr_cl_26_195;
741 [ # # ]: 0 : else if (host->ios.clock <= 52000000)
742 [ # # ]: 0 : pwrclass_val = (bus_width <= EXT_CSD_BUS_WIDTH_8) ?
743 : 0 : card->ext_csd.raw_pwr_cl_52_195 :
744 : 0 : card->ext_csd.raw_pwr_cl_ddr_52_195;
745 [ # # ]: 0 : else if (host->ios.clock <= 200000000)
746 : 0 : pwrclass_val = card->ext_csd.raw_pwr_cl_200_195;
747 : : break;
748 : : case MMC_VDD_27_28:
749 : : case MMC_VDD_28_29:
750 : : case MMC_VDD_29_30:
751 : : case MMC_VDD_30_31:
752 : : case MMC_VDD_31_32:
753 : : case MMC_VDD_32_33:
754 : : case MMC_VDD_33_34:
755 : : case MMC_VDD_34_35:
756 : : case MMC_VDD_35_36:
757 [ # # ]: 0 : if (host->ios.clock <= 26000000)
758 : 0 : pwrclass_val = card->ext_csd.raw_pwr_cl_26_360;
759 [ # # ]: 0 : else if (host->ios.clock <= 52000000)
760 [ # # ]: 0 : pwrclass_val = (bus_width <= EXT_CSD_BUS_WIDTH_8) ?
761 : 0 : card->ext_csd.raw_pwr_cl_52_360 :
762 : 0 : card->ext_csd.raw_pwr_cl_ddr_52_360;
763 [ # # ]: 0 : else if (host->ios.clock <= 200000000)
764 : 0 : pwrclass_val = card->ext_csd.raw_pwr_cl_200_360;
765 : : break;
766 : : default:
767 : 0 : pr_warning("%s: Voltage range not supported "
768 : : "for power class.\n", mmc_hostname(host));
769 : 0 : return -EINVAL;
770 : : }
771 : :
772 [ # # ]: 0 : if (bus_width & (EXT_CSD_BUS_WIDTH_8 | EXT_CSD_DDR_BUS_WIDTH_8))
773 : 0 : pwrclass_val = (pwrclass_val & EXT_CSD_PWR_CL_8BIT_MASK) >>
774 : : EXT_CSD_PWR_CL_8BIT_SHIFT;
775 : : else
776 : 0 : pwrclass_val = (pwrclass_val & EXT_CSD_PWR_CL_4BIT_MASK) >>
777 : : EXT_CSD_PWR_CL_4BIT_SHIFT;
778 : :
779 : : /* If the power class is different from the default value */
780 [ # # ]: 0 : if (pwrclass_val > 0) {
781 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
782 : : EXT_CSD_POWER_CLASS,
783 : : pwrclass_val,
784 : : card->ext_csd.generic_cmd6_time);
785 : : }
786 : :
787 : 0 : return err;
788 : : }
789 : :
790 : : /*
791 : : * Selects the desired buswidth and switch to the HS200 mode
792 : : * if bus width set without error
793 : : */
794 : 0 : static int mmc_select_hs200(struct mmc_card *card)
795 : : {
796 : : int idx, err = -EINVAL;
797 : : struct mmc_host *host;
798 : : static unsigned ext_csd_bits[] = {
799 : : EXT_CSD_BUS_WIDTH_4,
800 : : EXT_CSD_BUS_WIDTH_8,
801 : : };
802 : : static unsigned bus_widths[] = {
803 : : MMC_BUS_WIDTH_4,
804 : : MMC_BUS_WIDTH_8,
805 : : };
806 : :
807 [ # # ]: 0 : BUG_ON(!card);
808 : :
809 : 0 : host = card->host;
810 : :
811 [ # # ][ # # ]: 0 : if (card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V &&
812 : 0 : host->caps2 & MMC_CAP2_HS200_1_2V_SDR)
813 : 0 : err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
814 : :
815 [ # # ][ # # ]: 0 : if (err && card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_8V &&
[ # # ]
816 : 0 : host->caps2 & MMC_CAP2_HS200_1_8V_SDR)
817 : 0 : err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
818 : :
819 : : /* If fails try again during next card power cycle */
820 [ # # ]: 0 : if (err)
821 : : goto err;
822 : :
823 : 0 : idx = (host->caps & MMC_CAP_8_BIT_DATA) ? 1 : 0;
824 : :
825 : : /*
826 : : * Unlike SD, MMC cards dont have a configuration register to notify
827 : : * supported bus width. So bus test command should be run to identify
828 : : * the supported bus width or compare the ext csd values of current
829 : : * bus width and ext csd values of 1 bit mode read earlier.
830 : : */
831 [ # # ]: 0 : for (; idx >= 0; idx--) {
832 : :
833 : : /*
834 : : * Host is capable of 8bit transfer, then switch
835 : : * the device to work in 8bit transfer mode. If the
836 : : * mmc switch command returns error then switch to
837 : : * 4bit transfer mode. On success set the corresponding
838 : : * bus width on the host.
839 : : */
840 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
841 : : EXT_CSD_BUS_WIDTH,
842 : 0 : ext_csd_bits[idx],
843 : : card->ext_csd.generic_cmd6_time);
844 [ # # ]: 0 : if (err)
845 : 0 : continue;
846 : :
847 : 0 : mmc_set_bus_width(card->host, bus_widths[idx]);
848 : :
849 [ # # ]: 0 : if (!(host->caps & MMC_CAP_BUS_WIDTH_TEST))
850 : 0 : err = mmc_compare_ext_csds(card, bus_widths[idx]);
851 : : else
852 : 0 : err = mmc_bus_test(card, bus_widths[idx]);
853 [ # # ]: 0 : if (!err)
854 : : break;
855 : : }
856 : :
857 : : /* switch to HS200 mode if bus width set successfully */
858 [ # # ]: 0 : if (!err)
859 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
860 : : EXT_CSD_HS_TIMING, 2, 0);
861 : : err:
862 : 0 : return err;
863 : : }
864 : :
865 : : /*
866 : : * Handle the detection and initialisation of a card.
867 : : *
868 : : * In the case of a resume, "oldcard" will contain the card
869 : : * we're trying to reinitialise.
870 : : */
871 : 0 : static int mmc_init_card(struct mmc_host *host, u32 ocr,
872 : : struct mmc_card *oldcard)
873 : : {
874 : : struct mmc_card *card;
875 : : int err, ddr = 0;
876 : : u32 cid[4];
877 : : unsigned int max_dtr;
878 : : u32 rocr;
879 : 0 : u8 *ext_csd = NULL;
880 : :
881 [ # # ]: 0 : BUG_ON(!host);
882 [ # # ]: 0 : WARN_ON(!host->claimed);
883 : :
884 : : /* Set correct bus mode for MMC before attempting init */
885 [ # # ]: 0 : if (!mmc_host_is_spi(host))
886 : 0 : mmc_set_bus_mode(host, MMC_BUSMODE_OPENDRAIN);
887 : :
888 : : /*
889 : : * Since we're changing the OCR value, we seem to
890 : : * need to tell some cards to go back to the idle
891 : : * state. We wait 1ms to give cards time to
892 : : * respond.
893 : : * mmc_go_idle is needed for eMMC that are asleep
894 : : */
895 : 0 : mmc_go_idle(host);
896 : :
897 : : /* The extra bit indicates that we support high capacity */
898 : 0 : err = mmc_send_op_cond(host, ocr | (1 << 30), &rocr);
899 [ # # ]: 0 : if (err)
900 : : goto err;
901 : :
902 : : /*
903 : : * For SPI, enable CRC as appropriate.
904 : : */
905 [ # # ]: 0 : if (mmc_host_is_spi(host)) {
906 : 0 : err = mmc_spi_set_crc(host, use_spi_crc);
907 [ # # ]: 0 : if (err)
908 : : goto err;
909 : : }
910 : :
911 : : /*
912 : : * Fetch CID from card.
913 : : */
914 [ # # ]: 0 : if (mmc_host_is_spi(host))
915 : 0 : err = mmc_send_cid(host, cid);
916 : : else
917 : 0 : err = mmc_all_send_cid(host, cid);
918 [ # # ]: 0 : if (err)
919 : : goto err;
920 : :
921 [ # # ]: 0 : if (oldcard) {
922 [ # # ]: 0 : if (memcmp(cid, oldcard->raw_cid, sizeof(cid)) != 0) {
923 : : err = -ENOENT;
924 : : goto err;
925 : : }
926 : :
927 : : card = oldcard;
928 : : } else {
929 : : /*
930 : : * Allocate card structure.
931 : : */
932 : 0 : card = mmc_alloc_card(host, &mmc_type);
933 [ # # ]: 0 : if (IS_ERR(card)) {
934 : : err = PTR_ERR(card);
935 : 0 : goto err;
936 : : }
937 : :
938 : 0 : card->ocr = ocr;
939 : 0 : card->type = MMC_TYPE_MMC;
940 : 0 : card->rca = 1;
941 : 0 : memcpy(card->raw_cid, cid, sizeof(card->raw_cid));
942 : : }
943 : :
944 : : /*
945 : : * For native busses: set card RCA and quit open drain mode.
946 : : */
947 [ # # ]: 0 : if (!mmc_host_is_spi(host)) {
948 : 0 : err = mmc_set_relative_addr(card);
949 [ # # ]: 0 : if (err)
950 : : goto free_card;
951 : :
952 : 0 : mmc_set_bus_mode(host, MMC_BUSMODE_PUSHPULL);
953 : : }
954 : :
955 [ # # ]: 0 : if (!oldcard) {
956 : : /*
957 : : * Fetch CSD from card.
958 : : */
959 : 0 : err = mmc_send_csd(card, card->raw_csd);
960 [ # # ]: 0 : if (err)
961 : : goto free_card;
962 : :
963 : 0 : err = mmc_decode_csd(card);
964 [ # # ]: 0 : if (err)
965 : : goto free_card;
966 : 0 : err = mmc_decode_cid(card);
967 [ # # ]: 0 : if (err)
968 : : goto free_card;
969 : : }
970 : :
971 : : /*
972 : : * Select card, as all following commands rely on that.
973 : : */
974 [ # # ]: 0 : if (!mmc_host_is_spi(host)) {
975 : 0 : err = mmc_select_card(card);
976 [ # # ]: 0 : if (err)
977 : : goto free_card;
978 : : }
979 : :
980 [ # # ]: 0 : if (!oldcard) {
981 : : /*
982 : : * Fetch and process extended CSD.
983 : : */
984 : :
985 : 0 : err = mmc_get_ext_csd(card, &ext_csd);
986 [ # # ]: 0 : if (err)
987 : : goto free_card;
988 : 0 : err = mmc_read_ext_csd(card, ext_csd);
989 [ # # ]: 0 : if (err)
990 : : goto free_card;
991 : :
992 : : /* If doing byte addressing, check if required to do sector
993 : : * addressing. Handle the case of <2GB cards needing sector
994 : : * addressing. See section 8.1 JEDEC Standard JED84-A441;
995 : : * ocr register has bit 30 set for sector addressing.
996 : : */
997 [ # # ][ # # ]: 0 : if (!(mmc_card_blockaddr(card)) && (rocr & (1<<30)))
998 : 0 : mmc_card_set_blockaddr(card);
999 : :
1000 : : /* Erase size depends on CSD and Extended CSD */
1001 : 0 : mmc_set_erase_size(card);
1002 : : }
1003 : :
1004 : : /*
1005 : : * If enhanced_area_en is TRUE, host needs to enable ERASE_GRP_DEF
1006 : : * bit. This bit will be lost every time after a reset or power off.
1007 : : */
1008 [ # # ][ # # ]: 0 : if (card->ext_csd.enhanced_area_en ||
1009 [ # # ]: 0 : (card->ext_csd.rev >= 3 && (host->caps2 & MMC_CAP2_HC_ERASE_SZ))) {
1010 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
1011 : : EXT_CSD_ERASE_GROUP_DEF, 1,
1012 : : card->ext_csd.generic_cmd6_time);
1013 : :
1014 [ # # ]: 0 : if (err && err != -EBADMSG)
1015 : : goto free_card;
1016 : :
1017 [ # # ]: 0 : if (err) {
1018 : : err = 0;
1019 : : /*
1020 : : * Just disable enhanced area off & sz
1021 : : * will try to enable ERASE_GROUP_DEF
1022 : : * during next time reinit
1023 : : */
1024 : 0 : card->ext_csd.enhanced_area_offset = -EINVAL;
1025 : 0 : card->ext_csd.enhanced_area_size = -EINVAL;
1026 : : } else {
1027 : 0 : card->ext_csd.erase_group_def = 1;
1028 : : /*
1029 : : * enable ERASE_GRP_DEF successfully.
1030 : : * This will affect the erase size, so
1031 : : * here need to reset erase size
1032 : : */
1033 : 0 : mmc_set_erase_size(card);
1034 : : }
1035 : : }
1036 : :
1037 : : /*
1038 : : * Ensure eMMC user default partition is enabled
1039 : : */
1040 [ # # ]: 0 : if (card->ext_csd.part_config & EXT_CSD_PART_CONFIG_ACC_MASK) {
1041 : 0 : card->ext_csd.part_config &= ~EXT_CSD_PART_CONFIG_ACC_MASK;
1042 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_PART_CONFIG,
1043 : : card->ext_csd.part_config,
1044 : : card->ext_csd.part_time);
1045 [ # # ]: 0 : if (err && err != -EBADMSG)
1046 : : goto free_card;
1047 : : }
1048 : :
1049 : : /*
1050 : : * Enable power_off_notification byte in the ext_csd register
1051 : : */
1052 [ # # ]: 0 : if (card->ext_csd.rev >= 6) {
1053 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
1054 : : EXT_CSD_POWER_OFF_NOTIFICATION,
1055 : : EXT_CSD_POWER_ON,
1056 : : card->ext_csd.generic_cmd6_time);
1057 [ # # ]: 0 : if (err && err != -EBADMSG)
1058 : : goto free_card;
1059 : :
1060 : : /*
1061 : : * The err can be -EBADMSG or 0,
1062 : : * so check for success and update the flag
1063 : : */
1064 [ # # ]: 0 : if (!err)
1065 : 0 : card->ext_csd.power_off_notification = EXT_CSD_POWER_ON;
1066 : : }
1067 : :
1068 : : /*
1069 : : * Activate high speed (if supported)
1070 : : */
1071 [ # # ]: 0 : if (card->ext_csd.hs_max_dtr != 0) {
1072 : : err = 0;
1073 [ # # ][ # # ]: 0 : if (card->ext_csd.hs_max_dtr > 52000000 &&
1074 : 0 : host->caps2 & MMC_CAP2_HS200)
1075 : 0 : err = mmc_select_hs200(card);
1076 [ # # ]: 0 : else if (host->caps & MMC_CAP_MMC_HIGHSPEED)
1077 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
1078 : : EXT_CSD_HS_TIMING, 1,
1079 : : card->ext_csd.generic_cmd6_time);
1080 : :
1081 [ # # ]: 0 : if (err && err != -EBADMSG)
1082 : : goto free_card;
1083 : :
1084 [ # # ]: 0 : if (err) {
1085 : 0 : pr_warning("%s: switch to highspeed failed\n",
1086 : : mmc_hostname(card->host));
1087 : : err = 0;
1088 : : } else {
1089 [ # # ][ # # ]: 0 : if (card->ext_csd.hs_max_dtr > 52000000 &&
1090 : 0 : host->caps2 & MMC_CAP2_HS200) {
1091 : 0 : mmc_card_set_hs200(card);
1092 : 0 : mmc_set_timing(card->host,
1093 : : MMC_TIMING_MMC_HS200);
1094 : : } else {
1095 : 0 : mmc_card_set_highspeed(card);
1096 : 0 : mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
1097 : : }
1098 : : }
1099 : : }
1100 : :
1101 : : /*
1102 : : * Compute bus speed.
1103 : : */
1104 : : max_dtr = (unsigned int)-1;
1105 : :
1106 [ # # ]: 0 : if (mmc_card_highspeed(card) || mmc_card_hs200(card)) {
1107 [ # # ]: 0 : if (max_dtr > card->ext_csd.hs_max_dtr)
1108 : : max_dtr = card->ext_csd.hs_max_dtr;
1109 [ # # ][ # # ]: 0 : if (mmc_card_highspeed(card) && (max_dtr > 52000000))
1110 : : max_dtr = 52000000;
1111 [ # # ]: 0 : } else if (max_dtr > card->csd.max_dtr) {
1112 : : max_dtr = card->csd.max_dtr;
1113 : : }
1114 : :
1115 : 0 : mmc_set_clock(host, max_dtr);
1116 : :
1117 : : /*
1118 : : * Indicate DDR mode (if supported).
1119 : : */
1120 [ # # ]: 0 : if (mmc_card_highspeed(card)) {
1121 [ # # ]: 0 : if ((card->ext_csd.card_type & EXT_CSD_CARD_TYPE_DDR_1_8V)
1122 [ # # ]: 0 : && ((host->caps & (MMC_CAP_1_8V_DDR |
1123 : : MMC_CAP_UHS_DDR50))
1124 : : == (MMC_CAP_1_8V_DDR | MMC_CAP_UHS_DDR50)))
1125 : : ddr = MMC_1_8V_DDR_MODE;
1126 [ # # ]: 0 : else if ((card->ext_csd.card_type & EXT_CSD_CARD_TYPE_DDR_1_2V)
1127 [ # # ]: 0 : && ((host->caps & (MMC_CAP_1_2V_DDR |
1128 : : MMC_CAP_UHS_DDR50))
1129 : : == (MMC_CAP_1_2V_DDR | MMC_CAP_UHS_DDR50)))
1130 : : ddr = MMC_1_2V_DDR_MODE;
1131 : : }
1132 : :
1133 : : /*
1134 : : * Indicate HS200 SDR mode (if supported).
1135 : : */
1136 [ # # ]: 0 : if (mmc_card_hs200(card)) {
1137 : : u32 ext_csd_bits;
1138 : 0 : u32 bus_width = card->host->ios.bus_width;
1139 : :
1140 : : /*
1141 : : * For devices supporting HS200 mode, the bus width has
1142 : : * to be set before executing the tuning function. If
1143 : : * set before tuning, then device will respond with CRC
1144 : : * errors for responses on CMD line. So for HS200 the
1145 : : * sequence will be
1146 : : * 1. set bus width 4bit / 8 bit (1 bit not supported)
1147 : : * 2. switch to HS200 mode
1148 : : * 3. set the clock to > 52Mhz <=200MHz and
1149 : : * 4. execute tuning for HS200
1150 : : */
1151 [ # # ][ # # ]: 0 : if ((host->caps2 & MMC_CAP2_HS200) &&
1152 : 0 : card->host->ops->execute_tuning) {
1153 : : mmc_host_clk_hold(card->host);
1154 : 0 : err = card->host->ops->execute_tuning(card->host,
1155 : : MMC_SEND_TUNING_BLOCK_HS200);
1156 : : mmc_host_clk_release(card->host);
1157 : : }
1158 [ # # ]: 0 : if (err) {
1159 : 0 : pr_warning("%s: tuning execution failed\n",
1160 : : mmc_hostname(card->host));
1161 : 0 : goto err;
1162 : : }
1163 : :
1164 [ # # ]: 0 : ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ?
1165 : : EXT_CSD_BUS_WIDTH_8 : EXT_CSD_BUS_WIDTH_4;
1166 : 0 : err = mmc_select_powerclass(card, ext_csd_bits);
1167 [ # # ]: 0 : if (err)
1168 : 0 : pr_warning("%s: power class selection to bus width %d"
1169 : : " failed\n", mmc_hostname(card->host),
1170 : : 1 << bus_width);
1171 : : }
1172 : :
1173 : : /*
1174 : : * Activate wide bus and DDR (if supported).
1175 : : */
1176 [ # # ][ # # ]: 0 : if (!mmc_card_hs200(card) &&
1177 [ # # ]: 0 : (card->csd.mmca_vsn >= CSD_SPEC_VER_4) &&
1178 : 0 : (host->caps & (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA))) {
1179 : : static unsigned ext_csd_bits[][2] = {
1180 : : { EXT_CSD_BUS_WIDTH_8, EXT_CSD_DDR_BUS_WIDTH_8 },
1181 : : { EXT_CSD_BUS_WIDTH_4, EXT_CSD_DDR_BUS_WIDTH_4 },
1182 : : { EXT_CSD_BUS_WIDTH_1, EXT_CSD_BUS_WIDTH_1 },
1183 : : };
1184 : : static unsigned bus_widths[] = {
1185 : : MMC_BUS_WIDTH_8,
1186 : : MMC_BUS_WIDTH_4,
1187 : : MMC_BUS_WIDTH_1
1188 : : };
1189 : : unsigned idx, bus_width = 0;
1190 : :
1191 [ # # ]: 0 : if (host->caps & MMC_CAP_8_BIT_DATA)
1192 : : idx = 0;
1193 : : else
1194 : : idx = 1;
1195 [ # # ]: 0 : for (; idx < ARRAY_SIZE(bus_widths); idx++) {
1196 : 0 : bus_width = bus_widths[idx];
1197 [ # # ]: 0 : if (bus_width == MMC_BUS_WIDTH_1)
1198 : : ddr = 0; /* no DDR for 1-bit width */
1199 : 0 : err = mmc_select_powerclass(card, ext_csd_bits[idx][0]);
1200 [ # # ]: 0 : if (err)
1201 : 0 : pr_warning("%s: power class selection to "
1202 : : "bus width %d failed\n",
1203 : : mmc_hostname(card->host),
1204 : : 1 << bus_width);
1205 : :
1206 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
1207 : : EXT_CSD_BUS_WIDTH,
1208 : 0 : ext_csd_bits[idx][0],
1209 : : card->ext_csd.generic_cmd6_time);
1210 [ # # ]: 0 : if (!err) {
1211 : 0 : mmc_set_bus_width(card->host, bus_width);
1212 : :
1213 : : /*
1214 : : * If controller can't handle bus width test,
1215 : : * compare ext_csd previously read in 1 bit mode
1216 : : * against ext_csd at new bus width
1217 : : */
1218 [ # # ]: 0 : if (!(host->caps & MMC_CAP_BUS_WIDTH_TEST))
1219 : 0 : err = mmc_compare_ext_csds(card,
1220 : : bus_width);
1221 : : else
1222 : 0 : err = mmc_bus_test(card, bus_width);
1223 [ # # ]: 0 : if (!err)
1224 : : break;
1225 : : }
1226 : : }
1227 : :
1228 [ # # ]: 0 : if (!err && ddr) {
1229 : 0 : err = mmc_select_powerclass(card, ext_csd_bits[idx][1]);
1230 [ # # ]: 0 : if (err)
1231 : 0 : pr_warning("%s: power class selection to "
1232 : : "bus width %d ddr %d failed\n",
1233 : : mmc_hostname(card->host),
1234 : : 1 << bus_width, ddr);
1235 : :
1236 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
1237 : : EXT_CSD_BUS_WIDTH,
1238 : 0 : ext_csd_bits[idx][1],
1239 : : card->ext_csd.generic_cmd6_time);
1240 : : }
1241 [ # # ]: 0 : if (err) {
1242 : 0 : pr_warning("%s: switch to bus width %d ddr %d "
1243 : : "failed\n", mmc_hostname(card->host),
1244 : : 1 << bus_width, ddr);
1245 : 0 : goto free_card;
1246 [ # # ]: 0 : } else if (ddr) {
1247 : : /*
1248 : : * eMMC cards can support 3.3V to 1.2V i/o (vccq)
1249 : : * signaling.
1250 : : *
1251 : : * EXT_CSD_CARD_TYPE_DDR_1_8V means 3.3V or 1.8V vccq.
1252 : : *
1253 : : * 1.8V vccq at 3.3V core voltage (vcc) is not required
1254 : : * in the JEDEC spec for DDR.
1255 : : *
1256 : : * Do not force change in vccq since we are obviously
1257 : : * working and no change to vccq is needed.
1258 : : *
1259 : : * WARNING: eMMC rules are NOT the same as SD DDR
1260 : : */
1261 [ # # ]: 0 : if (ddr == MMC_1_2V_DDR_MODE) {
1262 : 0 : err = __mmc_set_signal_voltage(host,
1263 : : MMC_SIGNAL_VOLTAGE_120);
1264 [ # # ]: 0 : if (err)
1265 : : goto err;
1266 : : }
1267 : 0 : mmc_card_set_ddr_mode(card);
1268 : 0 : mmc_set_timing(card->host, MMC_TIMING_UHS_DDR50);
1269 : 0 : mmc_set_bus_width(card->host, bus_width);
1270 : : }
1271 : : }
1272 : :
1273 : : /*
1274 : : * Enable HPI feature (if supported)
1275 : : */
1276 [ # # ]: 0 : if (card->ext_csd.hpi) {
1277 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
1278 : : EXT_CSD_HPI_MGMT, 1,
1279 : : card->ext_csd.generic_cmd6_time);
1280 [ # # ]: 0 : if (err && err != -EBADMSG)
1281 : : goto free_card;
1282 [ # # ]: 0 : if (err) {
1283 : 0 : pr_warning("%s: Enabling HPI failed\n",
1284 : : mmc_hostname(card->host));
1285 : : err = 0;
1286 : : } else
1287 : 0 : card->ext_csd.hpi_en = 1;
1288 : : }
1289 : :
1290 : : /*
1291 : : * If cache size is higher than 0, this indicates
1292 : : * the existence of cache and it can be turned on.
1293 : : */
1294 [ # # ][ # # ]: 0 : if ((host->caps2 & MMC_CAP2_CACHE_CTRL) &&
1295 : 0 : card->ext_csd.cache_size > 0) {
1296 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
1297 : : EXT_CSD_CACHE_CTRL, 1,
1298 : : card->ext_csd.generic_cmd6_time);
1299 [ # # ]: 0 : if (err && err != -EBADMSG)
1300 : : goto free_card;
1301 : :
1302 : : /*
1303 : : * Only if no error, cache is turned on successfully.
1304 : : */
1305 [ # # ]: 0 : if (err) {
1306 : 0 : pr_warning("%s: Cache is supported, "
1307 : : "but failed to turn on (%d)\n",
1308 : : mmc_hostname(card->host), err);
1309 : 0 : card->ext_csd.cache_ctrl = 0;
1310 : : err = 0;
1311 : : } else {
1312 : 0 : card->ext_csd.cache_ctrl = 1;
1313 : : }
1314 : : }
1315 : :
1316 : : /*
1317 : : * The mandatory minimum values are defined for packed command.
1318 : : * read: 5, write: 3
1319 : : */
1320 [ # # ][ # # ]: 0 : if (card->ext_csd.max_packed_writes >= 3 &&
1321 [ # # ]: 0 : card->ext_csd.max_packed_reads >= 5 &&
1322 : 0 : host->caps2 & MMC_CAP2_PACKED_CMD) {
1323 : 0 : err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
1324 : : EXT_CSD_EXP_EVENTS_CTRL,
1325 : : EXT_CSD_PACKED_EVENT_EN,
1326 : : card->ext_csd.generic_cmd6_time);
1327 [ # # ]: 0 : if (err && err != -EBADMSG)
1328 : : goto free_card;
1329 [ # # ]: 0 : if (err) {
1330 : 0 : pr_warn("%s: Enabling packed event failed\n",
1331 : : mmc_hostname(card->host));
1332 : 0 : card->ext_csd.packed_event_en = 0;
1333 : : err = 0;
1334 : : } else {
1335 : 0 : card->ext_csd.packed_event_en = 1;
1336 : : }
1337 : : }
1338 : :
1339 [ # # ]: 0 : if (!oldcard)
1340 : 0 : host->card = card;
1341 : :
1342 : 0 : mmc_free_ext_csd(ext_csd);
1343 : 0 : return 0;
1344 : :
1345 : : free_card:
1346 [ # # ]: 0 : if (!oldcard)
1347 : 0 : mmc_remove_card(card);
1348 : : err:
1349 : 0 : mmc_free_ext_csd(ext_csd);
1350 : :
1351 : 0 : return err;
1352 : : }
1353 : :
1354 : : static int mmc_can_sleep(struct mmc_card *card)
1355 : : {
1356 [ # # ][ # # ]: 0 : return (card && card->ext_csd.rev >= 3);
1357 : : }
1358 : :
1359 : 0 : static int mmc_sleep(struct mmc_host *host)
1360 : : {
1361 : 0 : struct mmc_command cmd = {0};
1362 : 0 : struct mmc_card *card = host->card;
1363 : : int err;
1364 : :
1365 [ # # ]: 0 : if (host->caps2 & MMC_CAP2_NO_SLEEP_CMD)
1366 : : return 0;
1367 : :
1368 : 0 : err = mmc_deselect_cards(host);
1369 [ # # ]: 0 : if (err)
1370 : : return err;
1371 : :
1372 : 0 : cmd.opcode = MMC_SLEEP_AWAKE;
1373 : 0 : cmd.arg = card->rca << 16;
1374 : 0 : cmd.arg |= 1 << 15;
1375 : :
1376 : 0 : cmd.flags = MMC_RSP_R1B | MMC_CMD_AC;
1377 : 0 : err = mmc_wait_for_cmd(host, &cmd, 0);
1378 [ # # ]: 0 : if (err)
1379 : : return err;
1380 : :
1381 : : /*
1382 : : * If the host does not wait while the card signals busy, then we will
1383 : : * will have to wait the sleep/awake timeout. Note, we cannot use the
1384 : : * SEND_STATUS command to poll the status because that command (and most
1385 : : * others) is invalid while the card sleeps.
1386 : : */
1387 [ # # ]: 0 : if (!(host->caps & MMC_CAP_WAIT_WHILE_BUSY))
1388 : 0 : mmc_delay(DIV_ROUND_UP(card->ext_csd.sa_timeout, 10000));
1389 : :
1390 : 0 : return err;
1391 : : }
1392 : :
1393 : : static int mmc_can_poweroff_notify(const struct mmc_card *card)
1394 : : {
1395 [ # # ][ # # ]: 0 : return card &&
1396 [ # # ][ # # ]: 0 : mmc_card_mmc(card) &&
[ # # ][ # # ]
1397 : 0 : (card->ext_csd.power_off_notification == EXT_CSD_POWER_ON);
1398 : : }
1399 : :
1400 : 0 : static int mmc_poweroff_notify(struct mmc_card *card, unsigned int notify_type)
1401 : : {
1402 : 0 : unsigned int timeout = card->ext_csd.generic_cmd6_time;
1403 : : int err;
1404 : :
1405 : : /* Use EXT_CSD_POWER_OFF_SHORT as default notification type. */
1406 [ # # ]: 0 : if (notify_type == EXT_CSD_POWER_OFF_LONG)
1407 : 0 : timeout = card->ext_csd.power_off_longtime;
1408 : :
1409 : 0 : err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
1410 : : EXT_CSD_POWER_OFF_NOTIFICATION,
1411 : : notify_type, timeout, true, false);
1412 [ # # ]: 0 : if (err)
1413 : 0 : pr_err("%s: Power Off Notification timed out, %u\n",
1414 : : mmc_hostname(card->host), timeout);
1415 : :
1416 : : /* Disable the power off notification after the switch operation. */
1417 : 0 : card->ext_csd.power_off_notification = EXT_CSD_NO_POWER_NOTIFICATION;
1418 : :
1419 : 0 : return err;
1420 : : }
1421 : :
1422 : : /*
1423 : : * Host is being removed. Free up the current card.
1424 : : */
1425 : 0 : static void mmc_remove(struct mmc_host *host)
1426 : : {
1427 [ # # ]: 0 : BUG_ON(!host);
1428 [ # # ]: 0 : BUG_ON(!host->card);
1429 : :
1430 : 0 : mmc_remove_card(host->card);
1431 : 0 : host->card = NULL;
1432 : 0 : }
1433 : :
1434 : : /*
1435 : : * Card detection - card is alive.
1436 : : */
1437 : 0 : static int mmc_alive(struct mmc_host *host)
1438 : : {
1439 : 0 : return mmc_send_status(host->card, NULL);
1440 : : }
1441 : :
1442 : : /*
1443 : : * Card detection callback from host.
1444 : : */
1445 : 0 : static void mmc_detect(struct mmc_host *host)
1446 : : {
1447 : : int err;
1448 : :
1449 [ # # ]: 0 : BUG_ON(!host);
1450 [ # # ]: 0 : BUG_ON(!host->card);
1451 : :
1452 : 0 : mmc_get_card(host->card);
1453 : :
1454 : : /*
1455 : : * Just check if our card has been removed.
1456 : : */
1457 : 0 : err = _mmc_detect_card_removed(host);
1458 : :
1459 : 0 : mmc_put_card(host->card);
1460 : :
1461 [ # # ]: 0 : if (err) {
1462 : 0 : mmc_remove(host);
1463 : :
1464 : : mmc_claim_host(host);
1465 : 0 : mmc_detach_bus(host);
1466 : 0 : mmc_power_off(host);
1467 : 0 : mmc_release_host(host);
1468 : : }
1469 : 0 : }
1470 : :
1471 : 0 : static int _mmc_suspend(struct mmc_host *host, bool is_suspend)
1472 : : {
1473 : : int err = 0;
1474 [ # # ]: 0 : unsigned int notify_type = is_suspend ? EXT_CSD_POWER_OFF_SHORT :
1475 : : EXT_CSD_POWER_OFF_LONG;
1476 : :
1477 [ # # ]: 0 : BUG_ON(!host);
1478 [ # # ]: 0 : BUG_ON(!host->card);
1479 : :
1480 : : mmc_claim_host(host);
1481 : :
1482 [ # # ]: 0 : if (mmc_card_suspended(host->card))
1483 : : goto out;
1484 : :
1485 [ # # ]: 0 : if (mmc_card_doing_bkops(host->card)) {
1486 : 0 : err = mmc_stop_bkops(host->card);
1487 [ # # ]: 0 : if (err)
1488 : : goto out;
1489 : : }
1490 : :
1491 : 0 : err = mmc_cache_ctrl(host, 0);
1492 [ # # ]: 0 : if (err)
1493 : : goto out;
1494 : :
1495 [ # # ][ # # ]: 0 : if (mmc_can_poweroff_notify(host->card) &&
1496 [ # # ]: 0 : ((host->caps2 & MMC_CAP2_FULL_PWR_CYCLE) || !is_suspend))
1497 : 0 : err = mmc_poweroff_notify(host->card, notify_type);
1498 [ # # ]: 0 : else if (mmc_can_sleep(host->card))
1499 : 0 : err = mmc_sleep(host);
1500 [ # # ]: 0 : else if (!mmc_host_is_spi(host))
1501 : 0 : err = mmc_deselect_cards(host);
1502 : 0 : host->card->state &= ~(MMC_STATE_HIGHSPEED | MMC_STATE_HIGHSPEED_200);
1503 : :
1504 [ # # ]: 0 : if (!err) {
1505 : 0 : mmc_power_off(host);
1506 : 0 : mmc_card_set_suspended(host->card);
1507 : : }
1508 : : out:
1509 : 0 : mmc_release_host(host);
1510 : 0 : return err;
1511 : : }
1512 : :
1513 : : /*
1514 : : * Suspend callback
1515 : : */
1516 : 0 : static int mmc_suspend(struct mmc_host *host)
1517 : : {
1518 : : int err;
1519 : :
1520 : 0 : err = _mmc_suspend(host, true);
1521 : : if (!err) {
1522 : : pm_runtime_disable(&host->card->dev);
1523 : : pm_runtime_set_suspended(&host->card->dev);
1524 : : }
1525 : :
1526 : 0 : return err;
1527 : : }
1528 : :
1529 : : /*
1530 : : * This function tries to determine if the same card is still present
1531 : : * and, if so, restore all state to it.
1532 : : */
1533 : 0 : static int _mmc_resume(struct mmc_host *host)
1534 : : {
1535 : : int err = 0;
1536 : :
1537 [ # # ]: 0 : BUG_ON(!host);
1538 [ # # ]: 0 : BUG_ON(!host->card);
1539 : :
1540 : : mmc_claim_host(host);
1541 : :
1542 [ # # ]: 0 : if (!mmc_card_suspended(host->card))
1543 : : goto out;
1544 : :
1545 : 0 : mmc_power_up(host, host->card->ocr);
1546 : 0 : err = mmc_init_card(host, host->card->ocr, host->card);
1547 : 0 : mmc_card_clr_suspended(host->card);
1548 : :
1549 : : out:
1550 : 0 : mmc_release_host(host);
1551 : 0 : return err;
1552 : : }
1553 : :
1554 : : /*
1555 : : * Shutdown callback
1556 : : */
1557 : 0 : static int mmc_shutdown(struct mmc_host *host)
1558 : : {
1559 : : int err = 0;
1560 : :
1561 : : /*
1562 : : * In a specific case for poweroff notify, we need to resume the card
1563 : : * before we can shutdown it properly.
1564 : : */
1565 [ # # ][ # # ]: 0 : if (mmc_can_poweroff_notify(host->card) &&
1566 : 0 : !(host->caps2 & MMC_CAP2_FULL_PWR_CYCLE))
1567 : 0 : err = _mmc_resume(host);
1568 : :
1569 [ # # ]: 0 : if (!err)
1570 : 0 : err = _mmc_suspend(host, false);
1571 : :
1572 : 0 : return err;
1573 : : }
1574 : :
1575 : : /*
1576 : : * Callback for resume.
1577 : : */
1578 : 0 : static int mmc_resume(struct mmc_host *host)
1579 : : {
1580 : : int err = 0;
1581 : :
1582 [ # # ]: 0 : if (!(host->caps & MMC_CAP_RUNTIME_RESUME)) {
1583 : 0 : err = _mmc_resume(host);
1584 : : pm_runtime_set_active(&host->card->dev);
1585 : : pm_runtime_mark_last_busy(&host->card->dev);
1586 : : }
1587 : : pm_runtime_enable(&host->card->dev);
1588 : :
1589 : 0 : return err;
1590 : : }
1591 : :
1592 : : /*
1593 : : * Callback for runtime_suspend.
1594 : : */
1595 : 0 : static int mmc_runtime_suspend(struct mmc_host *host)
1596 : : {
1597 : : int err;
1598 : :
1599 [ # # ]: 0 : if (!(host->caps & MMC_CAP_AGGRESSIVE_PM))
1600 : : return 0;
1601 : :
1602 : 0 : err = _mmc_suspend(host, true);
1603 [ # # ]: 0 : if (err)
1604 : 0 : pr_err("%s: error %d doing aggessive suspend\n",
1605 : : mmc_hostname(host), err);
1606 : :
1607 : 0 : return err;
1608 : : }
1609 : :
1610 : : /*
1611 : : * Callback for runtime_resume.
1612 : : */
1613 : 0 : static int mmc_runtime_resume(struct mmc_host *host)
1614 : : {
1615 : : int err;
1616 : :
1617 [ # # ]: 0 : if (!(host->caps & (MMC_CAP_AGGRESSIVE_PM | MMC_CAP_RUNTIME_RESUME)))
1618 : : return 0;
1619 : :
1620 : 0 : err = _mmc_resume(host);
1621 [ # # ]: 0 : if (err)
1622 : 0 : pr_err("%s: error %d doing aggessive resume\n",
1623 : : mmc_hostname(host), err);
1624 : :
1625 : : return 0;
1626 : : }
1627 : :
1628 : 0 : static int mmc_power_restore(struct mmc_host *host)
1629 : : {
1630 : : int ret;
1631 : :
1632 : 0 : host->card->state &= ~(MMC_STATE_HIGHSPEED | MMC_STATE_HIGHSPEED_200);
1633 : : mmc_claim_host(host);
1634 : 0 : ret = mmc_init_card(host, host->card->ocr, host->card);
1635 : 0 : mmc_release_host(host);
1636 : :
1637 : 0 : return ret;
1638 : : }
1639 : :
1640 : : static const struct mmc_bus_ops mmc_ops = {
1641 : : .remove = mmc_remove,
1642 : : .detect = mmc_detect,
1643 : : .suspend = NULL,
1644 : : .resume = NULL,
1645 : : .power_restore = mmc_power_restore,
1646 : : .alive = mmc_alive,
1647 : : .shutdown = mmc_shutdown,
1648 : : };
1649 : :
1650 : : static const struct mmc_bus_ops mmc_ops_unsafe = {
1651 : : .remove = mmc_remove,
1652 : : .detect = mmc_detect,
1653 : : .suspend = mmc_suspend,
1654 : : .resume = mmc_resume,
1655 : : .runtime_suspend = mmc_runtime_suspend,
1656 : : .runtime_resume = mmc_runtime_resume,
1657 : : .power_restore = mmc_power_restore,
1658 : : .alive = mmc_alive,
1659 : : .shutdown = mmc_shutdown,
1660 : : };
1661 : :
1662 : 0 : static void mmc_attach_bus_ops(struct mmc_host *host)
1663 : : {
1664 : : const struct mmc_bus_ops *bus_ops;
1665 : :
1666 [ # # ]: 0 : if (!mmc_card_is_removable(host))
1667 : : bus_ops = &mmc_ops_unsafe;
1668 : : else
1669 : : bus_ops = &mmc_ops;
1670 : 0 : mmc_attach_bus(host, bus_ops);
1671 : 0 : }
1672 : :
1673 : : /*
1674 : : * Starting point for MMC card init.
1675 : : */
1676 : 0 : int mmc_attach_mmc(struct mmc_host *host)
1677 : : {
1678 : : int err;
1679 : : u32 ocr, rocr;
1680 : :
1681 [ # # ]: 0 : BUG_ON(!host);
1682 [ # # ]: 0 : WARN_ON(!host->claimed);
1683 : :
1684 : : /* Set correct bus mode for MMC before attempting attach */
1685 [ # # ]: 0 : if (!mmc_host_is_spi(host))
1686 : 0 : mmc_set_bus_mode(host, MMC_BUSMODE_OPENDRAIN);
1687 : :
1688 : 0 : err = mmc_send_op_cond(host, 0, &ocr);
1689 [ # # ]: 0 : if (err)
1690 : : return err;
1691 : :
1692 : 0 : mmc_attach_bus_ops(host);
1693 [ # # ]: 0 : if (host->ocr_avail_mmc)
1694 : 0 : host->ocr_avail = host->ocr_avail_mmc;
1695 : :
1696 : : /*
1697 : : * We need to get OCR a different way for SPI.
1698 : : */
1699 [ # # ]: 0 : if (mmc_host_is_spi(host)) {
1700 : 0 : err = mmc_spi_read_ocr(host, 1, &ocr);
1701 [ # # ]: 0 : if (err)
1702 : : goto err;
1703 : : }
1704 : :
1705 : 0 : rocr = mmc_select_voltage(host, ocr);
1706 : :
1707 : : /*
1708 : : * Can we support the voltage of the card?
1709 : : */
1710 [ # # ]: 0 : if (!rocr) {
1711 : : err = -EINVAL;
1712 : : goto err;
1713 : : }
1714 : :
1715 : : /*
1716 : : * Detect and init the card.
1717 : : */
1718 : 0 : err = mmc_init_card(host, rocr, NULL);
1719 [ # # ]: 0 : if (err)
1720 : : goto err;
1721 : :
1722 : 0 : mmc_release_host(host);
1723 : 0 : err = mmc_add_card(host->card);
1724 : : mmc_claim_host(host);
1725 [ # # ]: 0 : if (err)
1726 : : goto remove_card;
1727 : :
1728 : : return 0;
1729 : :
1730 : : remove_card:
1731 : 0 : mmc_release_host(host);
1732 : 0 : mmc_remove_card(host->card);
1733 : : mmc_claim_host(host);
1734 : 0 : host->card = NULL;
1735 : : err:
1736 : 0 : mmc_detach_bus(host);
1737 : :
1738 : 0 : pr_err("%s: error %d whilst initialising MMC card\n",
1739 : : mmc_hostname(host), err);
1740 : :
1741 : 0 : return err;
1742 : : }
|